Question about Audio & Video Receivers

1 Answer

Carver CT-17 pre-amp does not give me the front display.

Posted by on

  • Skallywag Aug 09, 2009

    System shuts down the display and when it heats up again the display is good. When the display dies the sound also dies, and the stereo is useless until the display goes live again.
    I have been living with it but it is starting to get annoying during a party when it shuts off.
    I have torn it apart but can not get it totally apart, so I will try again. The system also does a reset and I loose all my programmed stations and it resets to lowest FM frequency.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try replacing C901, a 47uF/25v capacitor that is part of the FL display circuit.

Posted on Jan 14, 2009

  • HiFiTech Jan 14, 2009

    Sorry- C901 is located on the power supply board. It's located next to D908, a small DIP rectifier.

  • HiFiTech Jan 14, 2009

    ARGH! You can't edit solutions. It's not C901, I misread the board. It's C908. Really sorry about that.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi There, I have a Marantz SR7005 Receiver and Bose 901 Series VI speakers with the Bose equalizer. I'm struggling to figure out the best way to connect the Bose equalizer/speakers to the SR7005. ...


It sounds like you've read one of my many posts on 901 deployment in the AV world.

Functionally, what is the difference between one amp with 'x' channels or 'x' mono amps? Nothing. Pre-outs don't know or care what else an external amp does.

According to this link http://www.ecoustics.com/electronics/products/new/642968.html those amps are 2- and 5-channel, respectively.

There was a time when I had two bridged-mono Carver Cube atmps (at a real 400 watts) pushing one 901 each but that was big time overkill.

I now use a Carver AV-406 (functionally the same as your MM7055) with the 901 EQ in between the AV Receiver's front pre-outs and two 110-watt channels. Other channels on the AV-406 pull subwoofer and surround back duties. My AVR directly powers only the center and surround speakers.

The MM7025 would work for you.

Jul 07, 2011 | Marantz SR7005 Receiver

1 Answer

I recently bought a carver c1000a theater reciever and i have a set of 501 bose and a set of 901 bose is there going to be any problem hooking up the active eq for the 901s?


Yup, theBose 901's need their own amplifier dedicated. Get yourself a nice Carver M-100T or M400 Cube and run 'em off the Active Eq attached to the C1000 Front Pre-Outs.

Just wondering, why is this a new question to ponder if you've had the 501's and 901's all along. They never could coexist on a single amp.

I have 901's up front and 301's all around.

Mar 24, 2011 | Audio & Video Receivers

1 Answer

I have the following equipment and am going crazy trying to figure out how they get connected together. I also have the Carver Multi CD player and Carver Cassette Deck which I was able to connect to the...


Get a separate amp for the 901's and the rest falls into place.

1,2, 5) Place the 901 Active EQ between the pre/main front OUT of the receiver and the TFM-55X. Attach the 901's. Keep track of the jumpers you remove from the receiver. Or replace the jumpers with RCA splitter cables so you still have pre/main connection but can share the output with the TFM.

3) Pinnacle subwoofer (self-powered?) to the subwoofer out of the receiver.

4) Bose (AMS???) 5. As surrounds on the receiver. Place the sub module toward the rear so it mates sonically and directionally with them.

What? No center speaker? I'd get something more robust with bass capabilities, like a pair Bose 301 series 1's because the tweeters face in one direction only.

Except for the amps and the cube stuff that is essentially what I have. 6.1 with full-range speakers everywhere.

Aug 31, 2010 | Onkyo TX-SR803 Receiver

1 Answer

I want to use my 901 speakers with the yamaha rx 797 receiver and also my bose 601 in same room can i do that?


I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver2_bing.gif will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great!

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers2_bing.gif and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers2_bing.gif.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier2_bing.gif that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.

Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.



Jan 05, 2010 | Yamaha RX-797 Receiver

1 Answer

Connecting NAD 314 Receiver\ preamp to Carver M-500t to speakers


Dear Tim,
Yes, you can connect your NAD as a preamp to the Carver power Amp.

Connect the NAD's pre-out to the input of the Carver Power Amp. You can then connect the Klipsch speaker to the Carver. Set the gain control on the NAD.

Now you should be able to control all the input and the main volume control from the NAD.

Mar 12, 2009 | Onkyo TX-SR803 Receiver

1 Answer

Pioneer vsx 90txv and bose EQ


I wrote this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great! With one caveat - My receiver actually has 5.1 analog Outputs so I can drive up to 6 external amplifiers if I want to (I drive 4). IF yours does NOT (*) we have to be creative in extracting the front two channels from your multi-channel receiver. The obvious alternative place would be at one of the few OUTputs on the back, assuming you have one free to use.

* I can't find your exact manual so I have to extrapolate features.

I see on the SR>6003< there are Pre Audio OUTS so I'm betting your receiver does, too.

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out; (or VCR or Tape Out if you don't have Pre Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

*** If you use a Tape or VCR Out you will NOT be able to SELECT the source you use for the 901 Pre-Outs for listening, or else the 901's will not get any sound sent their way. DO NOT USE the monitor switch for that source.

Feb 01, 2009 | Pioneer VSX-90TXV Receiver

1 Answer

Bose 901 equalizer


I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great!

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.

Jan 12, 2009 | Onkyo TX-SR605 Receiver

1 Answer

Looking for a good amplifier


Any 2-channel (or greater) receiver or integrated amp with at least one Tape Monitor loop; or any separate amplifier - will work. I would look fror one with true > 100 watts per channel, all channels driven, 20-20000kz + a few dB, with less than 0.5% Total Harmonic Distortion (in other words clean and powerful) should suffice. Specific brands don't matter. I'm partial to old Carver amps.

-----

However, should you get a multi-channel amp for the 901's you will be limited to using only 901's on it as the required Active Equalizer would affect all speakers attached to the amp, and conventional speakers would not sound right and could possibly be harmed by it's drastically-altered frequency response. Since using the Tape Monitor on modern DSP Receivers disables their digital inputs, that would limit what you could listen to, should you later decide to go with Cable Box, DVD, SACD, DVD-Audio, Blu-Ray, DTS etc.

* There are no some multichannel receivers out there that allow separating the preamp-amp circuitry for each channel to allow for differences in speaker processing. I think Marantz had one.

However, having a 901-based multichannel setup myself, I would highly recommend getting the Full Monte for video listening (below)...

In that case a separate stereo amp for the 901's would work. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.

---------

So to sum it up, I think you should start with a powerful, clean amp with few bells and whistles for the 901's and maybe later add a multichannel receiver with all the magicfor source control, DSP and to drive the other channels.




Jan 05, 2009 | Onkyo TX-DS747

1 Answer

Bose 901 series 2 speakers


I wrote most of this for a different receiver, but if you account for minor differences to your receiver this will work just fine.

There's good news and bad news. The bad news you need a separate amp because a multichannel receiver with Bose 901's attached as recommended for a standard stereo receiver will only sound right in STEREO on stereo analog material. The other speakers around the room are not designed to receive its Active Equalization and if you engage your Tape Monitor you will NOT BE ABLE TO HEAR DIGITAL sources at all. Tape Monitor is for analog stereo material only and on modern AV receivers it disables any digital inputs so you really can't use the Tape Monitor circuit or attached devices for modern digital sources. However, you can still employ the various DSP options to spread 2-channel analog source material around the room. I do.

The good news. I have a setup similar to what you want to do and it works great!

A separate stereo amp for the 901's was my solution. I run a Carver AV-406 (5-channel amp) for my 901's in Front, 2 Subwoofers and the Rear Surround channel, with the Active EQ between the receiver Front L&R Outputs and the 901's amp channels. My receiver controls everything and just drives the Center and Surround speakers.

You could get by with just a stereo amp for the 901's. A Carver M-200 is a good efficient amplifier that would have you cooking just fine (2x100W). Run it with the Active EQ between the receiver Front L&R Pre-Outputs ** and the 901's amp channels.

** Front Pre Out (or one of your analog Tape Outs) >>> Bose EQ Amplifer IN, then
Bose EQ Amplier OUT >>> new amplifier IN.


Attach the 901's to the new amp, set its volume to Max and run through your receiver's speaker level setup.

Write off the Tape Out as an input if you use it to extract the Front L&R channels. DO NOT monitor it or you'll chop the 901's out of the signal path AND kill any digital source audio in the receiver.

Nov 23, 2007 | Yamaha HTR-5790 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

605 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68250 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...