Question about Drills

Open Question

I have a Hilti TE22 and I cant get the bit out how do i change the bit?

Bit is not seized up

Posted by Anonymous on

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 123 Answers

SOURCE: hilti te-14 bit type? SDS+, SDS max?


Posted on Oct 29, 2009

  • 2176 Answers

SOURCE: I am the owner of a TE 905 Hilti Jackhammer,

If you havent found them yet call 1-800-879-8000 and they will be more than willing to help you.

Posted on Jul 16, 2009

  • 61 Answers


the bearing in the chuck is probly missing. replace the ball baering.

Posted on Oct 11, 2009

  • 165 Answers

SOURCE: Hilti TE 10 drill. It doesn't seem to hold the

Probably a missing ball problem---contact Hilti website.

Posted on Feb 27, 2010

  • 8404 Answers

SOURCE: how do you remove the bit from the chuck of a TE

Slide the collar on the chuck to the rear (toward the handle)

Posted on Nov 22, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need a cooling fan for hilti hammer drill te22

From my experience with Hilti tools, you have to send the tool back to them for repair. I have not had much luck in getting any parts from them. Sorry!

May 07, 2015 | Hilti Drills

1 Answer

Hi. I was drilling a few holes in concrete with my TE 56 HILTI and the drill bit become jammed. it began to smoke so i put a new set of brushes in it and still the same spins slow and smokes, any...

It sound like is has overheated or a bearing has seized. Take it to hilti. for nearest dealer. They will collect for a price.

Dec 11, 2012 | Drills

1 Answer

How to Replace Hilti TE22 chuck

You put the two flat sides on the end of the cap nut and lock them in a vice. You then put a wrench on the back side of the chuck which also has two flat sides. with the cap nut locked in a vise take the wrench and turn the retaining sleeve which has the two flat sides counterclockwise to break the cap nut loose. When it turns freely take the chuck out of the vise and turn the cap nut off. You then push the ribbed locking sleeve down to access an o-ring. You pull that off and it releases the locking sleeve and two roller bearings. You then pull off the retaining slv with the two flat sides and release the other two roller bearings. the chuck will then just pull off the shaft

Hope this helps

Sep 30, 2012 | Hilti TE 7-C 120V Rotary Hammer Drill

1 Answer

I need a switch and brushings for my HELTI TE22 Hammer Drill

You need to contact a Hilti dealer either in person or online.

May 14, 2012 | Hilti 284228 UH 650 Universal 1/2" Hammer...

1 Answer

Hilti te22 trigger problem

the switch for the TE22 has been discontinued for years. Your best bet is to find a used one on ebay. Since it is a double throw switch somtimes you can get away with jumping one side "the bad side" and getting it to work for a while. The cord goes on the top connectors and the motor on the bottom. If you determine that one of them is bad then take the cord wire and move it directly to the motor connection below and secure it with the motor screw. A quick drawing below to show what I mean.

Hope this helps



Nov 10, 2011 | Hilti Drills

1 Answer

Trigger switch on te22 dead.can I get a replacement or will something else fit

you can go to Hilti direct or find a local dealer by going to "" or calling them at 1-800-879-8000 and you can get the replacement. I would not try another switch.

Feb 12, 2011 | Hilti Hammering

1 Answer

Hilti te 10 - how do I change the bit ? and lock it good...

The end of the drill is 2 parts hold the bottom part(closes to the drill) and turn the top part (the end the bits in) and turn it a 1/4 turn counter clockwise that opens the chuck then pull the bit out to replace do the opposite. Don't let the end at the drill spin or it will come off the drill completely if that happens simply line it back up and tap it hard to get it back on

Nov 25, 2010 | Hilti Hammer Drill Bit TECX 1 In x 10 In...

Not finding what you are looking for?
Drills Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

75117 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides