Question about Dishwashers

Open Question

Whirlpool adp 962 dishwasher problem

The lights are flashing and it cannot be switched off by holding down the start button nor does it want to start the any of the programmes

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1073 Answers

SOURCE: whirlpool adp 8540 - 7 flashes

replace the control board in the console

Posted on Apr 10, 2008

Ad
  • 1 Answer

SOURCE: flashing start light starts ok with prerinse programme then switches off having done nothing

Green light flashing

Posted on May 14, 2009

  • 220 Answers

SOURCE: Whirlpool ADP 5500 dishwasher stops - light flashes 7 times.

It's a heating issue either a bad heater or bad sensor.

Posted on Sep 01, 2009

  • 46 Answers

SOURCE: Whirlpool dishwasher, flashing start button

you have a door suitch proble may sure the door is totaly close try that good luck

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Err code displayed and fails start


Turn the programme selector dial to the required programme.
The selector dial can be turned either clockwise
or counter-clockwise. The green pilot light of the button
9 starts flashing: the appliance is now switched on.
If you turn the programme selector dial to another programme
when the appliance is working, the red pilot light
of the button 9 will flash 3 times and the message Err is displayed to indicate a wrong selection.
The appliance will not perform the new selected programme.
• To switch the appliance off, turn the programme selector
dial to the position .
To cancel or change a running programme, switch the
appliance off by turning the programme selector dial to the
position
. Select the new programme by turning the selector
to the desired programme. Start the new programme
by pressing the button 9 again. The water in the tub will be
not emptied out.

Dado

Sep 25, 2014 | Zanussi Washing Machines

1 Answer

ERROR CODE 61


If you have Zanussi washing mashine
To enter diagnostics:
  1. Switch off the appliance
  2. Press and hold down START/PAUSE and any one of the option buttons simultaneously
  3. Holding down both buttons switch the appliance on by turning the programme selector one position to the right (clockwise)
  4. Continue to hold down the START/PAUSE and option buttons until the LED begins to flash (at least 2 seconds)
In the first selector position, the operation of the buttons and the relative Led's is checked; turning the selector knob clockwise activates the diagnostics cycle for the operation of the various components and displays any alarm conditions.

Apr 21, 2014 | Washing Machines

1 Answer

Wml520 programme panel is flashing


Remove power for some time, open the panel and check the connectors and contacts. When the power is switched on , press down the start/stop button.If the fault does not clear the suspect can be the controller board.

Jul 03, 2012 | Hotpoint Washing Machines

1 Answer

Can I turn the beeper off on the end of the washcycle on the DDY062 Hoover dishwasher. I want to put it on timer delay and dont want to be woken in the middle of the night.


These are the instructions taken directly from the DDY062 manual:
Alarm mute for the PROGRAMME END
The alarm for the programme end may be muted as follows:
IMPORTANT The dishwasher must be ALWAYS off before start this procedure.
1. Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound).
2. Keep the "PROGRAMME SELECTION" button pressed for at least 15 seconds (during this time, 2 audible signals will sound).
3. Release the button when the second audible signal sounds (3 "PROGRAMME SELECTION" indicator lights will come on).
4. Press the same button again: the 3 indicator lights (which indicate that the alarm is activated) will start flashing (to indicate that the alarm is off).
5. Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting.
To turn the alarm on again, follow the same procedure.

Jun 21, 2012 | Hoover Dishwashers

1 Answer

The start light is flashing on and off and the programmer wont change to another programme it stays on the normal programme and the dishwasher will not start


Seems to be relatively common. Ma doing one now with that exact problem. If you hold button in for about 10 seconds, it should reset.(switch off then on again to push start.). If same action continues, the electronic module needs to be replaced.

Dec 31, 2010 | Whirlpool 24 in. ADP5966 Free-standing...

2 Answers

Whirlpool adp 6600 will not function start light is just flashing


Whirlpool adp 6600 will not function start light is just flashing. Waht di I do?

Sep 17, 2009 | Whirlpool 24 in. ADP6940 Dishwasher

1 Answer

Whirlpool dishwasher, flashing start button


you have a door suitch proble may sure the door is totaly close try that good luck

Sep 07, 2009 | Whirlpool 24 in. ADP5962 Free-standing...

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Owen Barnes

Level 3 Expert

867 Answers

Brad Brown

Level 3 Expert

15633 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...