Question about Fuji DX-5 Digital Camera
ha right now i have the same problem and like everyone else i havent dropped it or damaged it.
Fuji being awesome as they are wont cover this in warranty and its about $230 + to get it fixed and reportedly comes back with more errors than before
so how about you try what i'm about to do and smash it with a hammer, in future try canon or something else.
I am now a photographer without a camera for two months my camera is barely a yr old.
Thank you fuji!!!
Posted on Mar 03, 2008
SOURCE: fuji finepix a510
Check out this link: www.digitalcamera-hq.com/digital-cameras/fuji-finepix-z1_question.html?qid=4289
After the basics, try dropping the camera on a carpeted area from about 2-3 feet. It worked for my Fuji A500 and 90% of the responders on the link. Everything on the web said it would cost ~$100 to fix. I was in the process of researching new cameras to buy and had nothing to lose by dropping it on the floor.
The error may be caused by debris in the zoom mechanism preventing it from working. Dropping the camera loosens the debris and voila!
Posted on Jul 07, 2008
This is just a suggestion, as I am not an expert.A couple of years ago I had a problem with my older, Fuji Finepix camera related to the computer downloads/programming and I found Fujifinepix web site. I sent them an email and they responded and did not charge anything. Could try that..
Posted on Oct 29, 2008
SOURCE: focus error
You will have to disassemble the unit. 2 screws on 1 side and 1 on the other and 2 on the bottom, pop the back off, being careful of the 2 ribbon cables attached to the rear and unock these cables and remove. 3 screws holding the top circuit board (remove the eye piece first and unplug the 2 cables attached to it) carefully unplug all cables attached to this top board and unscrew and remove (there is one on the bottom of the board that you must flip to unlatch. After you remove that board there is the power board... BE CAREFUL!!! The flash capacitor (the black tube looking unit on the bottom of this board) stores chrge and you WILL feel it if you touch the terminals... it they touch metal you will see fireworks so be careful. unplug the single red and black wire plug and unscrew the 3 screws here You do not have to remove the white plug with the 4 or 5 wires because you can just flip the board over out of the uni.. BE CAREFUL!!. unscrew the 2 silver screws securing the metal plate underneath and remove this plate. now remove the single screw left and pull out the lens assem. Here check 2 places... 1 is he zoom screw (it is behind the long silver panel) and also the focus screw (behind the shorter metal panel. Do one at a time. remove the screws from one of them and carefully lift off the motor plate. for he zoom line to metal ring on the screw into the groove of the lens (Shaped like a V) carefully screw the screws back in bu d ni tighten to tight, leave a LITTLE slack. (1/8 turn from tight). Now for the focus screw, remove the cover and align the ring to encase the top of the V The ring is shaped like < the lens is a > so just allow the rinng on the screw to "pinch" the top of the lens groove. secure like you did the other plate (dont forget to back out 1/8 of a turn) reassemble the opposite of disassembly and you are done... it look hard but it is actually pretty easy... any uestions email me at firstname.lastname@example.org
Posted on Feb 21, 2009
Tips for a great answer:
Mar 11, 2011 | Fuji Finepix S6500FD Digital Camera
Nov 23, 2009 | Fuji FinePix A500 Digital Camera
Oct 14, 2009 | Fuji FinePix A607 Digital Camera
Oct 29, 2008 | Fuji FinePix S6500 Digital Camera
May 24, 2008 | Fuji FinePix A500 Digital Camera
May 13, 2008 | Fuji FinePix A500 Digital Camera
Mar 05, 2017 | Fujifilm X10 12 Megapixel-4x Manual...
43 people viewed this question
Usually answered in minutes!