Question about Exercise & Fitness

1 Answer

What is error code e4 on vision fitness t9350?

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have an HRT9450 that is showing an E4 error code - but when I run the auto calibration it doesn't seem to finish.

It runs up the speeds and back down but then stops without ever showing 'end'.

When i then take the safety key off and replace it the E4 error code shows again.

The treadmill was working fine until I moved it a foot and then the error code shows - meaning I'm suspecting a lose cable but I don't know where to start looking for it.

Any advice?

Posted on Jan 21, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
maxtreadmill
  • 832 Answers

SOURCE: I turned on my treadmill after a long hiatus :)

E4: Solution 1. Check power to the treadmill, as insufficient voltage to the treadmill can cause this error to reoccur. Check the power socket that the tread is plugged into. Eliminate any extension cords or surge protectors (plug the tread directly into a functional power source). Make sure the circuit is not overloaded. Make sure the circuit is NON-GFI. 2. Calibrate (See engineering mode for specific treadmill). 3. If calibrations do not hold, replace upper console. Note: Usually simultaneous with an E6. E6: Solution 1. Check the elevation plug connection at the lower board. 2. Check ALL large data cable connection at the lower and upper boards. 3. Calibrate (See engineering mode for specific treadmill) 4. Test/change large data cable (use large data cable information provided in the data cable portion of this Guide). 5. Replace elevation motor E7/E9: Solution 1. Certain lower boards have an LED that flashes when the magnet on the roller passes the sensor. Adjust sensor position if LED does not flash. See lower board basic troubleshooting for lower boards with the LED. 2. Unplug RPM sensor at the lower board. Check continuity. Treadmill will operate without sensor but cannot Autocalibrate. Calibrate manually. 3. Replace RPM sensor TREADMILL.TROUBLESHOOTING. AUTO CALIBRATION STEP 1 ENTER ENGINEERING MODE • With the SAFETY KEY in place, hold the “ELEVATION UP” and “SPEED DOWN” buttons for 5 seconds. “DGA3” will appear in the profile window and “EHG1” will appear in the function window. • You are now in ENGINEERING MODE STEP 2 ENTER AUTO CALIBRATIONS • Press the “ELEVATION UP” or “SPEED UP” to “EHG4”. • Press “SELECT”. STEP 3 • Press “START”. The treadmill will calibrate itself. This will take about 3 to 5 minutes. When AUTO is complete, “END” will appear in the window. Wait 10 to 15 seconds and the treadmill will reset itself to “P1”. STEP 4 • Press “START” to test the treadmill

Posted on May 06, 2010

guru_fixya
  • 944 Answers

SOURCE: Vision Fitness T9450 Treadmill error code "E4."

Hi,

E4 means
- Elevation parameters out of range
- Recalibrate it

If you want to calibrate it see the manual page no 5.

Click here to download the manual

post a comment for further assistance.
Thank you for using fixya have a nice day:-)

Posted on Sep 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does error code R5232 Failed mean on Vision Fitness T9600HRT treadmill


If you wish to get some details about treadmill error codes ; check the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Dec 04, 2016 | Vision Fitness Exercise & Fitness

1 Answer

Error code E1 and E4


PDF]SERVICE Manual - Quietside

https://www.quietside.com/archives/.../Service%20ACC1800C.pdf
When error occurs in air conditioner, error code is displayed on indoor unit .... Display priority order at overlapping error : E1?E4?E5?P0?P0?P5?P6?t1? ...

Midea air conditioner error codes

airmaster.net/midea-air-conditioner-error-codes/
Midea air conditioner error codes. Indoor unit error code explanation: R series: ... E1, Indoor / outdoor units communication protection. E2, Zero-crossing signal error ... E4, Outdoor unit temp. sensor or connector of temp. sensor is defective.

[PDF]Download the Fault Error Code Booklet - Samsung


Dec 05, 2015 | Heating & Cooling

1 Answer

E4 coming up on my screen display , what is this and how do I fix it so it will work again ....


What device are you talking about your stereo ATV a computer or a cell phone?

Most manufacturers have a support site on the Internet and given the error code and the model number they'll give you a solution

Nov 25, 2014 | Vision Fitness T9250 Deluxe Folding...

1 Answer

ERROR CODE E4 ?


Go to utube https://www.youtube.com
and type in your brand of printer / copier and ask after that how to fix error code E4 .

Example : how to fix error code E4 on a HP model 2400

Aug 12, 2014 | Office Equipment & Supplies

1 Answer

E4 error code beautyrest electric blanket


beauty rest electric blanket error code - akaQA

www.akaqa.com > Uncategorized
beauty rest electric blanket error code. What does error code E4 mean? Answer this. 0 Views: 2487 Answers: 1 Posted: 3 years ago. Comment this question.

E4 error code beautyrest electric blanket - Fixya

www.fixya.com/support/t22178587-e4_error_code_beautyrest_electric
Dec 13, 2013 - E4 error code beautyrest electric blanket One side works the other returns an "E4" error code - Simmons Beautyrest Microfleece question.

Dec 13, 2013 | Simmons Beautyrest Microfleece Electric...

1 Answer

Vision Fitness T960 treadmill error code E4 I was going to recalabrat hit start could hear machine turn off


please proceed according and fix it. See the diagram for troubleshooting and see my personal TIPS for motor help.
"E04": Incline motor wrong, check if the VR of the incline motor connects well or replug it. The
mark of the DC motor and control board should be matched connected. Sometimes you also test the wires from motor and restart the treadmill
1_8_2013_6_30_59_pm.jpg

Jan 08, 2013 | Exercise & Fitness

1 Answer

What causes e4 in an airconditioner


Read your instruction manual section troubleshooting for to see the error code.
if you do not have go to www.fitness.manualsonline.com or www. retrevo.com or www. manualsfactory.com

God bless you

May 09, 2012 | Heating & Cooling

1 Answer

Error code E4 is on our display of our KDW243A dishwasher - what does this mean please?


Error code E4 means there is an overflow. Water is probably trapped. If you get error code E4, just tilt the machine back about 45 degrees and let the water drain out. It should come out on both sides. Then, you should be good to go.

Dec 14, 2010 | Kenwood Dishwashers

1 Answer

I am getting a C4 on my T9350 Vission Fitness treamill. Please help. Thanks.


Hi,
Thanks for using Fixya.
C4 error indicates Elevation error (signal lost).
To remove it, check condition of all cables and cable connections and recalibrate

Jan 10, 2010 | Dmm Vision Fitness T9500 Treadmill

2 Answers

E4 Error


york hvac unit e4 error code Troubleshooting

Aug 05, 2008 | DeLonghi CF210 Portable Air Conditioner

Not finding what you are looking for?
Exercise & Fitness Logo

Related Topics:

802 people viewed this question

Ask a Question

Usually answered in minutes!

Top Exercise & Fitness Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Howard
Howard

Level 2 Expert

115 Answers

Tom Chichester

Level 3 Expert

35762 Answers

Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...