Question about Teac AG-D9260 Receiver

Open Question

How do I reset Protect on a Teac AG-9260 AV - Teac AG-D9260 Receiver

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4234 Answers

SOURCE: Receiver keeps flashing "PROTECT"

The protect message indicates that a problem was detected in the last stage of the amplifier and that it has shutdown to prevent further damage. Usually this indicates that the output transistors have failed. Any shop that works on audio should be able to repair this. Expect a part cost in the $20-$40 range. Add in the local labor rate for the total repair cost.

Dan

Posted on Dec 17, 2008

Ad

SOURCE: TEAC AG-D9100 freeze

Always be that legend when the audio amplifier IC damaged

Posted on May 08, 2009

  • 70 Answers

SOURCE: how to remove the protect signal

Make sure that your input level are not too high. They will cause the an overload in the receiver and it will clip the circuit. This will continue until you lower the level of the input that you have on at that time.


IF THIS HELPS PLEASE VOTE.....GOOD LUCK AND THANKS..

Posted on Nov 12, 2009

  • 1 Answer

SOURCE: Teac AG-V8525 Stopped producing sound. Has legend says "protect"

hit reset button back of receiver

Posted on Dec 02, 2009

caroldon
  • 17130 Answers

SOURCE: user manual AV receiver TEAC AG-L800

Please check this link for support:

http://www.teac.eu/hifi-audio/support/

Posted on Oct 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my Teac ag h500 keep saying protect?


Hi. Unfortunately the protection circuit is saving your speakers from a fault, most likely one side of the amplifier in the unit is defective.

This needs an engineer.

Service manual is here if you need it. TEAC AG H500 Manual AM FM Stereo Receiver HiFi Engine

Oct 02, 2016 | Teac Audio Players & Recorders

1 Answer

Can I connect an active speaker to the Teac AG d7900 output


http://produto.mercadolivre.com.br/MLB-184407791-av-digital-home-theater-receiver-teac-ag-d7900-_JM

It would have helped to know something morwe about the 'active' speaker.I imagine its manual would tell you what it needs for input.

Active speakers are usually designed to be driven by volume-controlled Line Level inputs. This receiver has none except for the Subwoofer PRE Output.

Aug 17, 2011 | Teac AG-D7900 Receiver

1 Answer

My receiver is flashing "protect" how do I reset it


The protect message indicates that a problem was detected at the final stage of the amplifier and the unit has been shutdown to prevent further damage.

If the unit continues to flash protect even with the speaker wires disconnected, then the problem is internal to the unit and it will require repair not just a reset. The typical reason for this is shorted output transistors. Expect a repair cost of $25-$45 for parts if it continues with the protect message.

Please keep us posted.

Thanks,
Dan

Jun 13, 2010 | Teac AG-V8060 Receiver

3 Answers

How to remove the protect signal


Make sure that your input level are not too high. They will cause the an overload in the receiver and it will clip the circuit. This will continue until you lower the level of the input that you have on at that time.


IF THIS HELPS PLEASE VOTE.....GOOD LUCK AND THANKS..

Nov 12, 2009 | Teac AG-D8900 Receiver

1 Answer

How do you reset the blinking protect banner on the ag-v8520?


Try disconnecting the power cord then disconnect the speakers. Plug the power cord back in then hold in the power button until the unit "clicks." Then disconnect the power cord and reconnect the speakers, then the power cord and turn it back on.

Jun 13, 2009 | Teac AG-V8060 Receiver

2 Answers

TEAC AG-D9100 freeze


Always be that legend when the audio amplifier IC damaged

May 08, 2009 | Teac AG-D9100 Receiver

1 Answer

TEAC DIGITAL HOME RECEIVER AGD 8900 AV


I changed the diodos from power supply.
I thought that help you offered
was free,but I forget that nothing here is free.
Thank you anyway









Dec 15, 2008 | Teac AG-D8900 Receiver

2 Answers

Teac g-v8520 protect problem


Check the thermal sensor, TH1. This causes the unit to go into protect, it is a common failure part on this model.

Oct 26, 2007 | Teac AG-D8900 Receiver

Not finding what you are looking for?
Teac AG-D9260 Receiver Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Teac Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5151 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Teac Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...