Question about Health & Beauty

Open Question

How to fix error 3 on wristech blood pressure monitor

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2712 Answers

SOURCE: blood pressure monitor problem

The two numbers that measure your blood pressure are written like a fraction: one number on top and one on the bottom. The top number in a blood pressure reading refers to the systolic pressure. It measures the pressure inside your blood vessels at the moment your heart beats. The bottom number represents your diastolic pressure. It measures the pressure in your blood vessels when your heart is resting between heartbeats. A good blood pressure for most people will be under 120/80, as most people with blood pressure problems have high blood pressure. However, extreme low blood pressure can also be a serious health concern.

Posted on Aug 27, 2008

Ad
r321567499
  • 74 Answers

SOURCE: error display

This link will allow you to troubleshoot questions...I hope this helps.

http://www.samsunghealthyliving.com/support.asp

Posted on Jan 07, 2009

Max J
  • 22 Answers

SOURCE: WITH AUTOMATIC CUFF BLOOD PRESSURE MONITOR GETTING ERROR

E might represents insufficient inflation for your mom. For automatic inflation monitors usually there is a mechanism to keep inflating the cuff to higher pressures for people with higher BP. Check how is done. In some auto monitors,while cuff is inflated you keep pressing on START button until pressure reaches to some 15 to 20 mmHg higher than the pressure that auto usually stops and displays E.

Posted on Sep 08, 2009

DrRonJupiter
  • 10 Answers

SOURCE: mabis automaic blood pressure cuff, pressure monitor

Dear Edward: Likely, either cuff not tight enough or not in correct location on your arm or not holding device at correct height. Make sure you use Lithium Ion batteries. Try it on someone else. Dr Ron Grassi,Jupiter,Florida.USA. www.DrGrassi.com 30ad4e8.jpg

Posted on Oct 13, 2009

  • 1 Answer

SOURCE: what does error 3 on my microlife blood pressure

I have digital blood pressure monitor Model 302 made in japan. It is not working. when start shoes error 3. Please advise

Posted on Dec 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is error code E3 on Wristech wrist blood pressure monitor Model HL 168ZA


The E3 Fault Code means Error in determining measurement data. In which case, measure again. If this continues to happen contact HoMedics Customer Service @ 800-466-3342.

http://blog.suntechmed.com/blog/23-abpm/310-top-5-reasons-your-automated-bp-monitor-gave-an-error-code

Feb 25, 2015 | Health & Beauty

1 Answer

I have put in two new batteries, but when I take my blood pressure it says "err"


Make sure that when you power it on, you let it sit for a minute before you test the pressure. The unit has to stabilize first.

Oct 21, 2013 | Wristech Blood Pressure Monitor

2 Answers

I got a wristech jb5538,i don;t have a manuel,can;t find 1 online.i need to know how to switch between kpa and mmhg


i got a wristech jb5538,i don;t have a manuel,can;t find 1 online.i need to know how to switch between kpa and mmhg.

the solution is when the unit is off, press and hold the left (<) button
until you see a kpa or mmhg in the display.
release then press and hold the same (<) button to choose between
kpa and mmhg .
press the start stop button to start measuring.

I also requested a manual from
info@jobar.com they sent me one.

Aug 10, 2011 | Asseenontvguys Wristech Blood Pressure...

1 Answer

I purchase a Wristech blood pressure band but I do not understand the reading such 132 sys/88 DIA & 90 PUL /min could you tell me what that mean?


I bought a wristech blood pression monitor its not working IT takes my blood pression very low. 74/64. I know my blood pression isnn't that low, is there something wrong with this monitor. Deb

Dec 18, 2010 | RTO WrisTech Blood Pressure & Pulse...

1 Answer

My wristech bp moniter will only pump up to 08 and then it displays the error message, what's wrong with it?


You need to make sure that the bp is RIGHT over the pulse point, that is the only way for them to read. they are great little items, but I prefer the arm cuff, have used them for 15 years on all my patients, the reading seems to me to be more steady and accurate. but, I know you already have to wrist, so please check the locations that you are placing it on your wrist. Please write back should you need more info, would love to make sure you are on schedule..... Guy

Sep 08, 2010 | Asseenontvguys Wristech Blood Pressure...

1 Answer

How do I reset my monitor clear the deck wipe it clean as if it was new? wristech model ZSBP-002


Press both the memory and on/off buttons at the same time. Hold for a couple seconds and monitor will reset.

Dec 08, 2009 | RTO WrisTech Blood Pressure & Pulse...

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Health & Beauty Experts

Robin Hill
Robin Hill

Level 3 Expert

1263 Answers

wcdoc1953
wcdoc1953

Level 2 Expert

280 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...