Question about Nintendo Video Game Consoles & Games

1 Answer

Wii Remote will turn on (1st light blinks, stays on steady for about 5 seconds) but then shuts off. To navigate anywhere on the wii I have to CONTINUALLY press buttons to turn it back on. Extremely frustrating, please help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Well we just went threw the same issue . check battery and the reconect .

Posted on Feb 17, 2012

  • kaufman_melo Feb 19, 2012

    I had just changed the batteries, but when I changed them again, voila. Thank you :)

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

My remotes were synced to another wii how do I re-sync them?


Step by step instructions on how to sync the Wii Remote or Wii Remote Plus to the Wii console using Standard Mode.

Note:

Only a Wii Remote in Standard Mode can turn the Wii console power ON or OFF.

What to Do:

  1. Press the Power button on the Wii console to turn it on.
  2. Open the SD Card Slot cover on the front of the Wii console. If you are using a Wii mini, the sync button is located left hand side next to the battery compartment. The sync button is a darker shade of red than the console.
  3. Remove the battery cover on the back of the Wii Remote to be synced.
    • Some models of the Wii Remote include a hole in the battery cover and a tool on the wrist strap to push the SYNC Button with. With this model, the battery cover does not need to be removed to access the SYNC button.
  4. Press and release the SYNC button just below the batteries on the Wii Remote; the Player LED on the front of the Wii Remote will blink. While the lights are still blinking, quickly press and release the red SYNC button on the Wii console.
    wiiremotesynchstandard.gif
  5. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
  6. This sync procedure must be followed for each additional Wii Remote added to the system.

May 19, 2014 | Nintendo Wii Console

1 Answer

I can't seem to sync my wii controller. All 4 lites are blinking and will not stop. I changed the batteries and tried to re-sync the controller w/no luck. It was just working a few minutes ago.


    Try these steps!

  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.


  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.


  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

    1. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.


    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.


    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).


    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).


    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.
if nothing else works call 1-800-255-3700

Jul 12, 2011 | Nintendo Wii Remote Controller

1 Answer

When sychronizing the wii balance board we held the sychronize button down to long and now the wii remote control won't work how do we fix this


1. Insert a Wii Balance Board compatible game disc in the Wii console.

2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.

3. Open the small SD Card slot cover on the front of the Wii console.

4. Remove the Battery Cover on the bottom of the Wii Balance Board.

5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.

6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.

7. The blue light will stop blinking and stay on steady once the synchronization is complete


Click here to download repair guide

Jan 05, 2011 | Nintendo Wii Console

1 Answer

I can not re start my nintendo balance board,


1. Insert a Wii Balance Board compatible game disc in the Wii console.

2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.

3. Open the small SD Card slot cover on the front of the Wii console.

4. Remove the Battery Cover on the bottom of the Wii Balance Board.

5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.

6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.

7. The blue light will stop blinking and stay on steady once the syncronization is complete

Dec 20, 2010 | Nintendo Wii Fit - Balance Board + Game...

1 Answer

MY WII BALANCE BOARD IS CHARGED BUT THE BLUE LIGHT WONT STAY ON.


  1. Insert a Wii Balance Board compatible game disc in the Wii console.


  2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.


  3. Open the small SD Card slot cover on the front of the Wii console.


  4. Remove the Battery Cover on the bottom of the Wii Balance Board.


  5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.


  6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.


  7. The blue light will stop blinking and stay on steady once the syncronization is complete.

click here to download repair guide if u want

Dec 15, 2010 | Nintendo Wii Fit - Balance Board + Game...

1 Answer

Ok, well me and brother want to play Wii. But we only have one remote, And that remote wont turn on. We are getting like so mad. We've changed the batteries like 5 different times, we've tried Syning it,...


  • Check to make sure the Sensor Bar cord is inserted into the back of the Wii console and the Sensor Bar is centered above or below your TV screen (more info).
  • Make sure you are using fresh batteries in the Wii Remote.
  • The Wii Remote Controller should be used between 3 to 10 feet from the TV.
  • Make sure no objects are blocking the signals between the Sensor Bar, the Wii console, and the Wii Remote.
  • Check for interference from infra-red light sources, such as candles, sunlight, fireplaces, and stoves.
  • Radio frequency interference may cause the Wii Remote to work erratically. Check for wireless devices such as cordless phones, wireless computer keyboards or mice, or other similar devices, and move or turn them off.
or if the remote lights up briefly than goes out try this
    Try these steps!

  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

    1. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.

If you are still unable to get the Wii console to recognize your Wii Remote(s) after carefully following the steps above, please call 1-800-255-3700 for further assistance. [nintendos help line]


i hope this helps you and please vote for me

Dec 06, 2010 | Nintendo Wii Remote Controller

2 Answers

My wii fit balance board keeps blinking but will not stay on. batteries are good. cant find my instruction book. what could be my problem????


follow this
  1. Insert a Wii Balance Board compatible game disc in the Wii console.


  2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.

  3. Open the small SD Card slot cover on the front of the Wii console.

  4. Remove the Battery Cover on the bottom of the Wii Balance Board.

  5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.

  6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.

  7. The blue light will stop blinking and stay on steady once the syncronization is complete.

Jul 20, 2010 | Nintendo Video Game Consoles & Games

1 Answer

Bought 2nd hand wii fit, have just loaded disc and replaced batteries in board but power light not staying on board, flashes for about 30 seconds and then switches off. Does it need to be synchronised with...


    Hope this helps

    Try these steps!

  1. Insert a Wii Balance Board compatible game disc in the Wii console.

  2. Use the Wii Remote to select the Disc Channel from the Wii Menu, then select "Start" to begin the game. Press the A Button to bypass the wrist strap screen.

  3. Open the small SD Card slot cover on the front of the Wii console.
  4. Remove the Battery Cover on the bottom of the Wii Balance Board.
  5. Press and release the SYNC button on the Wii Balance Board. The blue light on the board will start blinking.
  6. Press and release the red SYNC button on the Wii console while the blue light on the board is still blinking.
  7. The blue light will stop blinking and stay on steady once the synchronization is complete.
please leave a good rating and testimonial if you appreciate my help. THNX

Mar 27, 2010 | Nintendo Wii Fit for Wii

1 Answer

I was trying to register the Wii Balance Board for my Wii Fit. I think I may have presses the sync button on the Wii console too long and caused my Wii remotes to become unregistered. How can I correct the...


Hey wva54ccc,

According to information provided by the manufacturer, holding the sync button down for a prolonged period does clear all synced devices from the Wii's memory. In order to "start from scratch" and resync your remotes, you'll want to do the following:

1) Turn the Wii off and unplug it for at least 1-2 minutes. After this time has elapsed, plug the Wii back in.

2) Turn the power on again, and press the "Sync" button on the front of your Wii console for 15 seconds when the "Health and Safety" screen is being displayed. This will clear all previously synced devices from the Wii's memory.

3) To sync a remote/accessory to the Wii, you'll need to press the small red button located just beneath the batteries. When you do so, the blue lights on the front of the remote/accessory should blink.

4) Next, quickly press the "Sync" button on the Wii console again.

5) After the "Player" LED light stops blinking and stays lit, the remote/accessory is synced and no further actions are necessary with that remote.

6) Repeat steps 3, 4 and 5 for each remote/accessory you wish to sync to your Wii.

Should following these steps not resolve the problem, I'd strongly suggest checking out Nintendo's Wii remote troubleshooting website for more information.

http://www.nintendo.com/consumer/systems/wii/en_na/ts/wiiremote.jsp

Hope this helps you out.

Sincerely,
Aaron
Go Ahead. Use Us.

Jul 23, 2008 | Video Game Consoles & Games

1 Answer

Wii fit


Have had this problem before with wii sports. What I did was turn off the wii console and unplug from the power, leave for a few seconds then turn it back on when the health & safety screen comes up
  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.


  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:
  4. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

  5. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

  6. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

  7. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).

Jun 23, 2008 | Nintendo Wii Console

Not finding what you are looking for?

Open Questions:

Video Game Consoles & Games Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles & Games Experts

Bee Santiago

Level 2 Expert

268 Answers

Raj Patel

Level 3 Expert

905 Answers

phil

Level 2 Expert

567 Answers

Are you a Nintendo Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...