Question about Bally Walk In 9 8"" X 19 3"" X 7 6"" high floor panels

Open Question

Where the reset button on my Bally nickel slot machine is

Bally nickel slot machine

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My samsung model RF4289Hars refrig ice machine wil not make ice now i pushed on the button then it said to push reset button where is that Gary


The reset button should be on the icemaker, mine is a clear rubber button, I have my icemaker in the door so you fridge maybe different.

Jun 09, 2015 | Samsung Refrigerators

2 Answers

Mantiwoc ice machine


try to run a full clean cycle with nickel safe cleaner.

Nov 26, 2014 | Refrigerators

1 Answer

How often should you clean the ice maker?


it depends on the quality of water in your water supply. If you get scale buildup easily, you need to descale and sanitize it as often as each month, if scale buildup is minimal, descale and sanitized every 6 monthes. I always nickel safe scale remover and calgon sanitizer. If in doubt, consult the manufactures recommendations.

May 25, 2013 | Scotsman Ice Maker 600LB CM3 30inW...

1 Answer

My brema ice machine dsnt wanna work, it just stopped. do they have reset buttons


Not really.
Check water supply and filter first. Then check to make sur the fill valve in the cube tray has not frozen shut.

It might only need to be defrosted and refrigeration coils cleaned of dust and debris..

Jan 15, 2012 | Refrigerators

1 Answer

Ice won't drop from ice tray


Hello, something is holding your Ice Slab at the bottom from your description.
Some causes are
1 Dirty - scaled up evap, or just dirty w muddy covering,
2 the vacuum breaking holes are stopped up If it is making a sla with the evaporator warm no ice take a flashlight and hold it where its shining to the back of the evap and look for the light on the cube forming slots next to the ones your shining the light into Upper corners of each hole must be open.
3 The slab is freezing uneve most like cause is a stopped up distributor tube at the top thats feeding the water down the evaporator.
4 On some models they had a closer fitting water curtian (the cover in front of the slab) and the top of the sheet touched this and caused the slab to stay upright and continue the "slide" forward.If your curtian is of the older style and has metal hooks on it with vertical slots n the curtian look at the slots and see if the slots are worn making the whole curtian slide down ward I have seen this several times.4B On some older models there is also a plastic coated wire diverter on the bottom infront of the evaporator. If the plastic coating is gone or the bottom or is not even, the slab could hang up there. 4C If you have the newer plastic pins make sure they are seated in the mounting properly.
5 Nickel plating could be coming off (any copper color on the lower 1/3 of the evaporator?).
6 I have seen some of the horizontal plates them selves be loose and not in flush try pushing and pulling on them especially the ones at the bottom. Any that are loose and coming out is your problem.
This lengthy extrapolation is by no means all of the possibilities but most of the common ones.

Thanks

Jul 12, 2010 | Frigidaire FRS3R5EMB Side by Side...

1 Answer

Machine beeps when turned on ice position cleaning cycle works but no ice is beeing made


first try resetting the board by pushing the reset button on the board. But make note of the number of the beeps before resetting.

Dec 21, 2009 | Hoshizaki KM-630M Crescent Cuber Ice Maker

1 Answer

"bin full" (full of somethin')


Thank you for following up with me. The machine works fine now. I should not have sent my message under the category of "similar problem" since I had already fixed it. My solution was simply to gently pull the sender and receiver units out, give them a good cleaning, and put them back in. Each unit looks like 2 LEDs attached to the end of a black plastic holder about 4" long. There were no screws to deal with. I just wiggled the plastic holders out, then back in. They are located (in the case of my machine) at the forward and rear ends of the narrow drop slot which leads into the ice holding bin below (as if to aim a beam across the length of the slot. A hand will have to be inserted an inch or two up into the drop slot to feel them along the wall of the slot.

Oct 03, 2009 | Scotsman Ice Maker 600LB CM3 30inW...

1 Answer

Bally coin slot machine wont let the handle pull


THIS IS DOCTOR FIX. MY BUSINESS IS GAMING REPAIR. (JUKE BOX=PINBALL= SLOT MACHINES
BOWLING =POKER, FOR 68 YEARS.) IF YOU HAVE NOT SOLVED YOU PROBLEM, I ASSUME IT IS ELECTRONIC, NOT MECHANICAL. IF MECHANICAL , LET ME KNOW, I WILL TELL YOU WHAT TO DO.
ON THE ELECTRONIC, OR ELECTRIC (NO COMPUTER)
THERE IS A BAR MOVES ON TO THE CAM ON TOP OF THE CATCH, ABOUT 3 INCHES ABOVE THE BOLT THAT HOLDS THE ARM IN PLACE, WHEN A COIN IS INSERTED INTO THE COIN SHOOT, THAT METAL BAR ENGAGES THE RATCHET , TO SPIN THE WHEELS. DOES THAT HAPPEN ON YOUR SLOT.? OPEN THE DOOR PULL THE WHITE SWITCH THAT CLOSE WHEN DOOR IS CLOSED (OUT) THESE ARE A THREE POSITION SWITCH.
IN-HOME JUKE BOX REPAIR
SEYLEVITT@JUNO.COM

HOPE IT HELPS.

May 03, 2009 | Bally Walk In 9 8"" X 19 3"" X 7 6"" high...

3 Answers

VENDO PEPSI 407 soda machine


selection number 7 reads sold out but its full i have a vendo drink machine that is electronic and i push the code button to test then select number 7 vend on first button then third button to test vend and it showed an error failed .what else could i try i need some sujestions. please.

Apr 23, 2009 | Refrigerators

1 Answer

Crushed ice only.No cubes.


Pull the ice bin out about 4 inches and re-insert it in the slot in the rear to reset the crusher arm.

Mar 11, 2009 | Whirlpool GD2SHGX Refrigerator

Not finding what you are looking for?
Bally Walk In 9 8"" X 19 3"" X 7 6"" high floor panels Logo

Related Topics:

819 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bally Refrigerators Experts

John Tripp
John Tripp

Level 3 Expert

4636 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Bally Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...