Question about Home Security

1 Answer

Dead kenwood kr9940

Garage sale unit, powers up no sound or needle movement

Posted by on

  • stevehalley4
    stevehalley4 Feb 16, 2012

    I am not real familiar with the insides of stereo gear could you lend a little guidence, I have checked the fuses they are good.

  • stevehalley4
    stevehalley4 Feb 16, 2012

    I know enough to not get to deep into it, but before I take it to a shop ,I wanted to rule out any simple fixes.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Have you checked the relays on the power/protection board? Fuses?

Posted on Feb 16, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Started to sew then stopped I think due to needle bent out of shape like a fish hook


good old sales pitch
fit a new needle and turn by hand to see where the needle is hitting.
open up the area near the teeth that pulls the material through and watch if the needle is hitting the bobbin carrier ( needle seat timing)
take it to a sewing machine repair shop ( most will quote on all makes of machines ) and see if it is fixable or best just to junk it

Sep 05, 2015 | Sewing Machines

1 Answer

Kenwood KDC-BT558u drains 640 constantly from the Battery even when the unit is off!


check the wire harness connections, sounds like you have KOER power hooked to KOEO. Or in other words, you have power to the radio with the key off that should connected to key on power

Jan 06, 2015 | Kenwood Car Audio & Video

1 Answer

Kenwood no sound


If you have a separate 'power' or sub-woofer amp, check that it still has power and did not blow a fuse. Is there an internal selection inside the unit for enabling the internal amp vs an external amp? Some will disable the internal amp using a setup setting, and just provide low level output that is expected to be amplified by an external amp. If it 'forgot' you might have to set it to use the internal amp again. Or vice-versa, depending.

Jul 23, 2014 | Kenwood KDC-S2009

2 Answers

PC Dell desktop has light on CD-R/W drive but cd is not opening (files not read). No sound of whirling/movement in drive; is it dead?


Turn the unit off...
Look at the face of the CD/DVD drive for a small hole.
Find a Hat pin or large needle and insert in that hole.
You can straiten out a paper clip
You must be level and not off to any sides..
This will give you access to whatever disk is in drive and remove it.
Close the drive and restart the unit.
If all looks ok, try a new CD or DVD.
If the same problem comes back, disconnect the power and IDE cable in the rear of the drive and replace with the same.

Sep 15, 2009 | Computers & Internet

1 Answer

I have a 2005 Corolla LE. with a single CD player. How do I find out the correct radio model number for my car? The CD player stopped working


I have just pulled out my original perfectly working '05 Corola single CD radio unit and have it in my hand. The label on top lists a Model NO. 86120-02430 ..... Rererence NO. CQ-JS7460X

Replaced with a Kenwood MP3 player, planning on selling original unit at a garage sale.

Ted78229@aol.com

Sep 04, 2009 | 2005 Toyota Corolla

1 Answer

Garage Door opened but will not close. I opened


I think the trolley has jammed against the bolt just in front of the motor unit. Remove the bolt and then run the door until it is closed. With the door closed locate the 'up limit' control on the side of the motor unit. Turn this 2 turns in the opposite direction of the arrow printed on the cover. Replace the bolt.

Sep 01, 2009 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Had my head unit from a Kenwood kvt-717dvd system stolen


i have a 717 no brain for sale ought at garage sale and was told all i neded were the wires. i had no clue it needs a brain .

May 10, 2009 | Kenwood KVT-717DVD Car DVD Player

1 Answer

Code retrival


this code was created and entered into the radio by the owner of this radio, not by kenwood this is an antitheft feature that cannot be undone without that person's help. Kenwood will not be able to "decode" this unit unfortunately

Mar 26, 2008 | Kenwood KDC-MPV622 CD Player

1 Answer

Zen vision m - dead


Sounds like its dead. Which could just mean the motherboard is shot and needs to be replaced. Hard to tell when it doesn't respond at all. You'll need to either take it apart and replace the motherboard, or send it to a technician who can. There is a chance though that the zen is too far gone to fix. 50% of the time, when a zen won't even power on when connected to a power source, its too far gone to fix.

Sep 15, 2007 | Creative Labs ZEN Vision:M Digital Media...

Not finding what you are looking for?
Home Security Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Home Security Experts

kakima

Level 3 Expert

102366 Answers

Brad Brown

Level 3 Expert

15478 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Are you a Home Security Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...