Question about Sceptre Dragon Eye D50X (White) 15 in.CRT Conventional Monitor

1 Answer

Sceptre D50X black screen

I have just purchased this monitor from a thrift shop..it looked new...the bags were not opened...the power cord still in the original bag..etc.... I plugged it into my computer and it came on for the windows loading screen then went black..the lights seem to be going through some kinda scan but will not stop and the monitor will not come on(light is on but no picture)Is there anything I need to do besides just plugging it in, like drivers etc...I am using windows XP for my OS and the monitor has a date of 2001 on the sticker. Any help would be greatly appreciated. Thanks Kenny

Posted by on

  • naturemomm Aug 13, 2008

    Have had the screen working on our computer for over two years. Last night it just went black. It will come on for a second or two after you power off and back on again. Any suggestions?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 105 Answers

If a monitor shows a normal screen at startup but goes bad after the Windows logo disappears, your Windows video setting is probably not compatible with the monitor. You can start Windows in safe mode to select a compatible resolution for your monitor.

Posted on Sep 04, 2006

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS THE 1994 FORD ESCORT AIRBAG CODE 34 REPAIR


Ford Airbag Fault Codes
Flash Code Component/Fault Description
- No Air Bag Indicator - Inoperative Indicator Circuit
- Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor
Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 Right Radiator Primary Crash Sensor Feed/Return Circuit Open
42 Left Radiator Primary Crash Sensor Feed/Return Circuit Open
44 Right Radiator Crash Sensor Not Mounted to Vehicle Properly
45 Left Radiator Crash Sensor Not Mounted to Vehicle Properly
51 Airbag diagnostic Monitor Internal thermal fuse Blown
52 Back-up Power supply Voltage Boost Fault
53 Front Crash Sensor High Resistance or Diagnostic Monitor Failure

Aug 12, 2014 | 1994 Ford Escort

6 Answers

Sceptre X32GV-Komodo


See troubleshooting (p.96-99) of user manual
but Unfortunately i think this problem is for Sceptre ...
For technical help, contact our Sceptre Technical Support Group via email or
phone. Please have your Sceptre p/n number, serial number, and date of
purchase available before you call.
Tech Support E-mail : monitor-ts@sceptre.com
Customer Service Email : cs@sceptre.com
TEL : 1800-788-2878
Operation Hours : Mon - Fri at 8:30 AM – 5:30 PM Pacific Standard Time

Mar 20, 2008 | Televison & Video

1 Answer

New power cord required for g4a kirby


Are you looking where to buy one? Any vac shop website should have one, Amazon, or Ebay.

Feb 15, 2014 | Kirby G4 Bagged Upright Vacuum

1 Answer

I purchased my Sceptre 32in tv in 2006. In the past 6-8 months I've noticed that the television has been taking extremely long to show the SCEPTRE screen after it has been turned on. Today I turned the...


The tv that take a long time to turn on.The cause is the tv power supply board,it not giving the tv the wright power voltages anymore.The power supply board,that the board,where the power a/c cord plug into it.Tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Oct 27, 2010 | Sceptre X32BV-Naga 32 in. LCD TV

2 Answers

Sceptre Monitor P/N X7G-Komodo II displays for about 1 second at a time, then goes black. When I cycle monitor power, I see a perfect display for 1 second. Does anyone have a recommended solution?


When the backlight does not stay on for more than a second, the problem is usually the backlight power supply board failure. Typical failures are blown capacitors, or transistors. A electronic repair shop should be able to fix it.

Oct 05, 2010 | Sceptre X7G Komodo II 17 in. Flat Panel...

1 Answer

My monitor wont come on it will have a white screen for moments then go black


Power supply will be the first place to look, make usre that it does put out 5vdc for logic and 12~18vdc for the backlight inverter circuits.
Most common failures in the LCD monitors are bad capacitors (bulging top/seal or leaking) in the power supply, blown fuses, poor solder jopints, failed inverter circuits (blown fuse, shorted transistors, shorted/open transformers), bad lamps (poor solder connections or worn out lamps). You will need to open it up and inspect the inside, see example of failed SCEPTRE monitors to get some ideas what to look for: http://s807.photobucket.com/home/budm/allalbums
Post back what you see inside so we can guide you further and it will help out other people in the future also.
http://en.wikipedia.org/wiki/Capacitor_plague
http://www.badcaps.net

Jun 07, 2010 | Sceptre X20G-Naga II 20.1" Flat Panel LCD...

1 Answer

How do you replace the bag on a Hoover Elite 200?


I had the same problem and just figured it out myself. Detach the clamp (attamched to the bag) from the handle. Then slide the bag out from the clamp either left or right. The cloth bag then opnes and you can replace the actual bag inside. Hope this helps.

Nov 11, 2009 | Vacuums

2 Answers

What is airbag light code 31 and 51 on a 1994 ford taurus


I was unable to locate code 31 in my book here is a copy of the codes. looks like you just need a fuse for #51. this may fix 31 as well.

Diagnostic Trouble Code Table 1994

AIR BAG DIAGNOSTIC MONITOR DIAGNOSTIC TROUBLE CODE PRIORITY TABLE
Priority Code Component/Fault Description
Highest - No Air Bag Indicator - Inoperative Lamp Circuit or No Ignition
Voltage to Air Bag Diagnostic Monitor

Continuous Air Bag Indicator - Air Bag Diagnostic Monitor
Disconnected or Inoperative
12 Low Battery Voltage
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Safing Sensor Not Mounted to Vehicle Properly
22 Safing Sensor Output Shorted to Battery Voltage
23 Safing Sensor Circuit Input Feed/Return Circuit Open
24 Safing Sensor Output Feed/Return Circuit Open
32 Driver Side Air Bag Module High Resistance or Open
33 Passenger Side Air Bag Module High Resistance or Open
34 Driver Side Air Bag Module Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Module Low Resistance or Shorted
42 Center Radiator Primary Crash Sensor Feed/Return Open
44 Center Cowl Primary Crash Sensor Not Mounted to Vehicle Properly
45 Center Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
51 Diagnostic Monitor Internal Thermal Fuse - Fuse Blown Due to
Intermittent Short to Ground
52 Backup Power Supply - Voltage Boost Fault
53 Primary Crash Sensor Circuits - Resistance to Ground or Air Bag
Diagnostic Monitor Failure

Lowest - Rapid Continuous Flashing of Air Bag Indicator (No DTC) All Primary

Sep 30, 2009 | 1994 Ford Taurus

1 Answer

Airbag light on. flashing 5 times 2 times then stays on


I think you have a false code stored due to your work. clear the code and you should be ok.
If the air bag indicator does not illuminate or the indicator stays on or flashes at any time, a fault has been detected by the air bag diagnostic monitor.
Diagnostic trouble codes (DTCs) may not be displayed for approximately 30 seconds after the ignition switch is placed in the RUN position. This is the amount of time the air bag diagnostic monitor requires to perform all tests and verify system faults.
Each DTC (a series of flashes and pauses of the air bag indicator):
  • Represents a two-digit number.
  • Is always displayed at least twice.
If the diagnostic monitor detects a fault in the air bag system, a diagnostic trouble code (DTC) will be written to the diagnostic monitor's Non-Volatile RAM (NVRAM). This DTC will then cause the lamp to flash a lamp fault code (LFC) on the air bag warning lamp and can be retrieved with the New Generation STAR (NGS) tester. After servicing the DTC may then be cleared from the NVRAM.
If a system fault is present and the air bag indicator is malfunctioning, an audible tone will be heard. The tone is a series of five sets of five beeps. If the tone is heard, the air bag system needs attention.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor will attempt to remove deployment power by turning on a solid state switch to blow the 10A battery fuse.

If the 10A battery fuse has successfully been blown by the air bag diagnostic monitor, the air bag diagnostic monitor will not attempt to blow it again until the proper fault has been repaired and cleared (refer to Diagnostic Instructions). The air bag diagnostic monitor will store both the unwanted deployment diagnostic trouble code and the loss of deployment power diagnostic trouble code. The loss of deployment power diagnostic trouble code is the highest priority.
If a fault exists that makes unwanted air bag deployment possible, the air bag diagnostic monitor has an internal fuse that that will blow (open) automatically. This removes all power to the air bag deployment circuit.
DTCs are prioritized numerically. If two or more faults occur at the same time, the fault having the highest priority will be displayed first. After that fault has been corrected, the next highest priority fault will be displayed.
The air bag diagnostic monitor includes an internal backup power supply. This feature provides sufficient backup power to deploy the air bag in the event the battery (10655) or battery cables are damaged in a collision before safing and air bag sensors close. The backup power supply will deplete its stored energy approximately one minute after the positive battery cable is disconnected.
---------------------------------------------------------------
Once a DTC is logged into the air bag diagnostic monitor memory, it will stay in memory until 80 key cycles have been recorded or until the NGS is used to erase the DTCs. Once 256 key cycles have been recorded since the concern was last detected, the DTC will automatically be removed from memory.
--------------------------------------------------------------
Active Command Modes
This command allows the technician to verify operation of the air bag system, indicator and tone. When the air bag output command is executed, the indicator and the tone are simultaneously activated for approximately four seconds. Both devices are automatically deactivated.


Air Bag Diagnostic Monitor DTC Priority Table DTC LFC Description Action To Take B1342 24 Air bag diagnostic monitor is faulted (retrieved only during On-Demand Self Test) GO to Pinpoint Test P . B1867 12/52 Lost or low battery voltage GO to Pinpoint Test A . B1869 — No air bag indicator — inoperative indicator circuit GO to Pinpoint Test R . B1913 13/53 Air bag circuit shorted to ground — driver/passenger GO to Pinpoint Test B . B1914 14/54 Air bag sensor circuit shorted to ground GO to Pinpoint Test C . B1921 21 Air bag diagnostic monitor ground circuit open or not mounted to the vehicle properly GO to Pinpoint Test D . B1922 22 Safing sensor output circuit shorted to battery voltage GO to Pinpoint Test E . B1924 24 System disarm fault GO to Pinpoint Test P . B1932 32 Driver side air bag module circuit high resistance or open GO to Pinpoint Test F . B1933 33 Passenger side air bag module circuit high resistance or open GO to Pinpoint Test G . B1934 34 Driver side air bag module circuit low resistance or shorted GO to Pinpoint Test H . B1935 35 Passenger side air bag module circuit low resistance or shorted GO to Pinpoint Test J . B1941 41 RH air bag sensor feed/return circuit open GO to Pinpoint Test K . B1942 42 LH air bag sensor feed/return circuit open GO to Pinpoint Test L . B1944 44 RH air bag sensor not mounted to the vehicle properly or ground circuit open GO to Pinpoint Test M . B1945 45 LH air bag sensor not mounted to the vehicle properly or ground circuit open GO to Pinpoint Test N .
DTC - Diagnostic Trouble Code, retrieved using New Generation STAR (NGS) Tester.
LFC - Lamp Fault Code, flashed on air bag indicator.

May 21, 2009 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Sceptre Dragon Eye D50X (White) 15 in.CRT Conventional Monitor Logo

523 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sceptre Computers & Internet Experts

Cindy Wells

Level 3 Expert

5521 Answers

Ricky Ostrom
Ricky Ostrom

Level 2 Expert

274 Answers

methjd

Level 2 Expert

78 Answers

Are you a Sceptre Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...