Question about Sangean DT110 AM/FM Radio

1 Answer

AM reception is not working

AM reception is off. Can't scan through all AM stations. As an example, it jumps from 927 to 936.

Posted by on

1 Answer

Re: AM reception is not working

Turn the power off and then press the UP tuning button several times, hold in the tuning up button and then turn power on and release both buttons. It should would work perfectly.

Posted on Sep 19, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Why no am reception on grundig 800 millinium satelite radio

It depends on your location. Set reception mode to AM waves. Dial in the frequency of the station or enter it using the keypad. To tune in on a station, rotate the radio.

Jul 19, 2014 | Grundig Satellit 800 AM/FM/SW Radio

1 Answer

Message says check reception. radio is in same location as always

This message means that the radio didn't receive the weekly check-in or test signal from the station it's tuned to, sometimes the station will fail to send it. To clear this message, simply turn the switch on the side of the radio off for a few seconds, then turn it back on.

May 31, 2014 | Midland WR-100 Weather/RDS Radio

1 Answer

Radio keeps scanning through all stations

Dab reception has frozen on my panasonic radio FM is OK .how do I fix

Sep 18, 2013 | Dewalt DC011 AM/FM Radio

1 Answer

AM will not work on my radio

It does not work at all or reception is bad? The radio has a ferrite bar antenna inside. Tune in to the frequency of the station you want and rotate the radio slowly to find the orientation for best reception. You may also try to hook an external AM antenna to the radio.

Sep 29, 2012 | Dewalt DC011 AM/FM Radio

1 Answer

Radio can only lock on one station

There are no known issues with the antenna connectors or cable.
Visually inspect the cable and ends to be sure nothing came loose.

Has there been anything added to the electronic system...i.e. HID headlights, amps, ect.

Call Iron cross Audio for more help.

Jun 25, 2012 | Harley Davidson 426290 AM/FM Radio

1 Answer

Emerson rp 6247 radio AM stations does not come in clear

Try moving the telescopic antenna around in different directions until you get a clear reception. If that doesn't work, try moving the whole unit (radio) to another location. Make sure you are using the tuning knob to switch between stations. Moving it to a different location may be the best thing because the radio antenna may be received in frequency waves from another electronic device (i.e. a television set, another radio or in microwave) which is causing a reception to be poor.

Mar 21, 2011 | Emerson RP6247S FM/Weather/AM/TV Radio

1 Answer

AM/FM stereo receiver often fully "drops" the reception of listened to radio station(s), or reception will often decrease in volume. Repositioning of the receiver's connected antenna wire often has no...

Possible solution. I have fixed two with this problem. When the radio drops to a hard surface, the ferrite coil antenna is the heaviest component on circuit board. Look for cracks in solder or broken wires where attachments to circuit board occurs for this component. Use a fine point soldering iron with low heat.

Oct 12, 2008 | Personal Radios

3 Answers

Excessive static on AM stations. Waves in and out. Not so on car radio. Is there an antenna to eliminate this?

Turn on the radio and turn the AM/SW BAND switch to the AM position. MW appears in the display. Use the outer ‘fast’ tuning knob to find stations, fine tuning with the inner ‘slow’ knob
when needed.

• If there is interference from adjacent stations, place the BAND WIDTH control in the NARROW position. If there is no interference, leave it in the WIDE position.

• If there is excess background noise, turn on
the SW LPF switch, which may minimize the noise.

• If a station is so strong that audio distortion occurs, reduce the gain level with the AM/SW RF GAIN control knob by turning it counterclockwise.

• The telescopic antenna does not have to be extended for AM reception. The radio has an internal, directional, ferrite-bar antenna for AM reception.

• To optimize AM reception, swivel the radio until maximum signal strength is achieved.

All of that being said: It's very tough nowadays to receive AM in this 2008 electronic world. If your able install a longwire SW antenna outside, and have access to a good earth ground, you can boost the AM signals and beat the noise being generated all around you.

Jan 08, 2008 | Grundig S350 AM/FM/SW Radio

2 Answers

AM reception/AM power problems

Don't take your radio to work. Get your work done , then go home and listen to it. You will get better reception in a res. area.

Oct 08, 2007 | RCA RP7887 High-Performance Super Radio

Not finding what you are looking for?
Sangean DT110 AM/FM Radio Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sangean Personal Radios Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 2 Expert

66 Answers

Mark Schmit
Mark Schmit

Level 3 Expert

1879 Answers

Are you a Sangean Personal Radio Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides