Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Water not draining out w/ spin cycle

Re: Whirlpool Ultimate Care Heavy Duty Super Capacity Plus 8 Cycle 2 Speed Motor

Hi! I'm unsure of the model number of this machine, first of all. It was purchased in 1997 (+/-). Everything is fine with my machine, except it just stopped draining the water with the last spin cycle. Thus, clothes are sopping wet when ready to go into the dryer. I'm still trying to decipher whether or not the second speed of the motor is functioning or not. Just guessing here. The center rotating piece is turning as normal with the first part of the cycle.

Any helpful advice would be appreciated. Thanks, in advance, for your help!

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,028 Answers

Sounds like water may be going out but no spin in last cycle lean washer back and ck underneath for oil leak on top off transmission is a silver colored disk shaped object this is part of clutch if there appears to be a lot of oil on it good chance there is oil on clutch also causing it not yo spin..also ck to see if basket spins after short pause at end of rinse cycle ..start a rinse cycle at setting on timer with lid shut allow to run undisturbed ..once agitation stops in rinse timer should stop then start motor back up to drain ..there should be another short pause then washer should start spinning if does not pause suspect suspect timer if it does pause but doesn't start spinning suspect transmission..remember allow washer to advance by itself DO NOT RAISE LID TO CK..a small load of clothes will let you know if washer has spun

Posted on Oct 26, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes it to stop intermittently?


http://www.appliancepartspros.com/whirlpool-motor-2-speed-wp661600-ap6010250.html
WP661600 is the motor part number for most of the Whirlpool Ultimate Care Washers. Your motor has a internal thermal protective fuse, which will open up, then re-close after a certain amount of "cooling down" time for the motor. You may want to wash smaller loads as to give the motor a break on amperage draw. the cost for the motor is around $125-$145. Also, check the timer for burn contacts.

Apr 03, 2017 | Whirlpool Washing Machines

1 Answer

My whirlpool ultimate Care II Heavy Duty Super Capacity Plus washer Very slightly agitates and don't spin dry


The motor coupler may be broken. Many Whirlpool®-manufactured washers use a small, relatively inexpensive motor coupling. It's plastic and rubber and is mounted to the shaft of the motor on one side, and to the transmission on the other. Over time, the coupler wears out and fails. You may need to replace it.

Mar 21, 2011 | Whirlpool Ultimate Care II LSQ9549L Top...

3 Answers

I have a Whirlpool Heavy Duty-Super Capacity Plus, 7cycle/2 speed. Model LSR7200EQO , the agitator stopped working


My whirlpool heavy duty 2 speed 7 cycle washer machine stopped working, It fills up and aggitates for the first cycle then when it should drain and spin it doesnt drain nor spin

Jun 05, 2010 | Whirlpool LSB6200KQ Top Load Washer

2 Answers

Find serial and model number


Normally on top load machines open the lid and look toward the back hinge area inside the lid. It is usually on the back there. It may also be posted on a white sticker on the back of the machine.

Apr 30, 2010 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Old Washer won't spin or agitate


You found a belt? Most w/p washer do not have a belt they are direct drive. take off the pump and motor to replace the motor coupling, 2 plastic pieces w/ a rubber in between

Feb 15, 2009 | Whirlpool Washing Machines

1 Answer

Washer spin & gurtitate no working


Coupling is broken that connects motor to transmission. Replace it. Please contact me if you need further help or leave feedback if appropriate as that is how I get paid. Thanks for letting me help you!

Nov 30, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Won't spin or agitate


coupling.between motor and gearcase.

Nov 11, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Agitator


if its a 2 piece agitator.. the gears in top of agitator is stripped out.. change gears be like new....spin top countor clockwise if it dont grap.. gears bad

Sep 28, 2007 | Whirlpool Ultimate Care II LSQ9549L Top...

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal De

Level 3 Expert

2672 Answers

yadayada
yadayada

Level 3 Expert

77514 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...