Question about Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Attempts to fill w/ water but won't...

Hello,

This washer just passed its one year mark and we now have a problem when trying to start a cycle. The machine will lock the door, spin once or twice, wait a few seconds and then attempts fill the machine with water. The sound it makes while trying is a medium to fast thumping sound, similar to a water pump that isn't passing water. This seems to go on indefinately, with no water filling the machine. I have checked the water at the hoses (is ok), and have checked the inlet valve screens (not clogged). Any help will be greatly appreciated.

Respectfully,
Sean

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 958 Answers

You can check the inlet solenoid coil. maybe there is no power coming to the coils or if there is power, the coil is burnt.


tnx 4 using fixya,

drcool

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag_lse7804ace: washer won't fill with water. If I fill it by hand, the cycle works fine (until it gets to the rinse cycle, when it won't fill again).


Hello John,
The most probable reason the washer is not filling is because of a blown fuse that is part of the lid switch asm. By UNPLUGGING THE WASHER and removing the 2 INNER screws on the the control panel and the control panel can be rotated down to see the fuse in the lid switch asm. Here is where the fuse is on the switch asm. its circled in red 11_4_2011_1_39_54_am.jpg

Nov 03, 2011 | Washing Machines

1 Answer

Won't stop filling up. Water continues to flow without stopping for cycles


Hello,

Their are 2 possibilites causing it to overflow

1) the water inlet valve that the hoses from the house plumbing attach to is sticking open,when it sticks it will stick open regardless if thier is power to the machine or not,so to determine if that is the problem,start the washer and quickly unplug it,if the water continues to fill, that valve is sticking

2) the water level switch is defective,do the same as far as starting it,if the fill stops when power disconected it's the water level switch that is in need of replacement

Good luck, i hope this helps.

Gene

Aug 28, 2011 | Kenmore 3.2 cu. ft. Plus Top Load Washer

1 Answer

Hi...my washer goes through cycles and then stops at "light" . It won't go through rinse and spin. Help


Make sure your cold water tape is turned on and the screen in the water valve is not plugged up, it may be trying to fill with cold water and cant get any, try filling the washer with cold water on a "wash" cycle to confirm it it fills with "cold" then just the rince cycle ion the timer may be faulty and would need to be replaced

Aug 25, 2011 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Won't fill, no cycling noises


Hello, try to see if there's a good water volume coming through the hoses attached to the washing machine.If there is, check to see if the screens inside the water-inlet valve are clean. (The water-inlet valve is the device on the washing machine that the fill hoses are attached to). If they're clean, you probably have a defective water-inlet valve. If so, you should completely replace the valve.

Thanks



Jun 04, 2010 | Kenmore 24642 Top Load Washer

1 Answer

Frigidaire (LTF2940E) Washer starts, stops, starts, stops...


The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.


  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

May 07, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Washer will not complete cycle


washer fills up but wont start washing i can turn the knob just passed the numbers and the little marks and it starts washing and when it gets to the rinse cycle it wont rinse but when it gets to spin cycle it spins good

Mar 16, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Washer will fill fill with water but doesn't start wash cycle


it will fill but won,t spin, will throw out water as if it washed, then it take water to rinse but won,t spin ,then will throw out water as if it did , but clothes are soaked

Feb 21, 2009 | Roper RAS8445KQ Top Load Washer

2 Answers

Frigidaire FTF530F won't advance


Possibly the timer. next time it wont stop filling turn off the washer. if it still fills you have a water valve issue. Hope for the valve. Timers are big bucks.

Jan 24, 2009 | Frigidaire FTF530FS Front Load Washer

1 Answer

Washer filled but does not run at all


When the unit completes its filling cycle, a relay will be activated to start the wash cycle. A 10 year old unit probably has dirty/corroded or otherwise malfunctioning relay contacts. This should be repaired by a qualified repairman as high voltages pass through these relays.

Mar 08, 2008 | Kenmore 24902 Top Load Washer

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...