Question about Channellock Channel Lock 4v Dual Driver

1 Answer

How to charge my channellock 4v drill. Can't find the instructions book

Can't find the instruction book and need to charge my drill. Can't see any place to plug the charger into the drill. Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,212 Answers

Traditionally the charge port is on the heel of the tool, it will be no larger than a screw head. It will have a small post terminal in the middle of it. If it does not have such a port, look for a soft polymeric button, it should flip out. If not, see if the battery can be released, the grayish buttons on the bottom of the handle may be what you need to press to release the battery for charging.

Posted on Feb 18, 2012

Testimonial: "Thanks, I found it."

  • 1 more comment 
  • lorenzo
    lorenzo Nov 16, 2013

    My drill does not rotate. Its locked. Any complaints about triggers not working or dirives not ging

  • lorenzo
    lorenzo Nov 16, 2013

    drives not moving.

  • lorenzo
    lorenzo Nov 16, 2013

    The charger blinks... every 15 seconds. The three lights are on at the top. The trigger will not move the drive. What could be the problem.


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My trigger switch works sometimes and then other times the trigger switch doesn't work and my light goes dead. Do I need to replace the switch and if so can you buy them.

Either the switch is bad or the wires going to/from the switch are loose and making intermittent contact. You need to open it up to see whats happening.

Feb 27, 2015 | Channellock Channel Lock 4v Dual Driver

3 Answers

Drill does not seem to be charging

you may need a new battery, their only good for so many charges.

Jul 05, 2014 | Channellock Channel Lock 4v Dual Driver

1 Answer

How to tell if charger is positive or negative?

Here you will found a possible solution:!AilOxaQiTdbQgdAbBgFAhCyiQS1HHg I include the manual and other considerations about the polarity,

May 21, 2014 | Channellock Channel Lock 4v Dual Driver

1 Answer

Manual download drill

"Manual download drill" - Please rephrase /clarify
"Cannot change bits" - More information needed.

Dec 26, 2013 | Channellock Channel Lock 4v Dual Driver

1 Answer


you must see the label attached to your charger. However if the label is NOT ATTACHED, please download the o.manual go to or www.
Other alternative is that you know what voltage is using the device that you are using, read the label attached of the device, and you must sure what is the charger specification.
God bless you

Nov 28, 2013 | Channellock Channel Lock 4v Dual Driver

1 Answer

Where can I find a replacement charger for this?

any charger that meets the requirement of voltage battery type and charge rate and the battery pack just fits in will do the job. It has to be suitable for either a nic cad battery pack or ni hi battery pack which require different chargers

Jun 29, 2013 | Channellock Channel Lock 4v Dual Driver

1 Answer

Where can I buy a battery for my CHannellock 24 volt rechargeable drill

Hi Sam...
The cheapest and greatest place I have found (amazon) is: Channellock 12V LITHIUM ION BATTERY Fits Channellock 12v tools
take a look and enjoy

Dec 11, 2011 | Drills

1 Answer

Battery will not charge

If you have DEEPLY discharged the driver, one or more cells of the battery have probably revese charged and shorted.They cannot be charged when this happens. Replace the battery is the solution.

Jul 31, 2011 | Channellock Channel Lock 4v Dual Driver

Not finding what you are looking for?
Channellock Channel Lock 4v Dual Driver Logo

Related Topics:

879 people viewed this question

Ask a Question

Usually answered in minutes!

Top Channellock Drills Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

75051 Answers

Brad Brown

Level 3 Expert

15451 Answers

Are you a Channellock Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides