Question about PC Laptops

Open Question

Packard Bell MotherBoard R6512 (PWA-8050MB/M BD)

During reboling South bridge U710 several elements were removed.. If someone have circuit diagram , please, share nominals of R838, R844, R845, R846, C785
thanks

Posted by on

6 Suggested Answers

SOURCE: packard bell easynote m5262

This is hard you have to take the laptop apart to get to the ram. but you have to remove the screen to get to the case screws.

Posted on Dec 08, 2007

  • 77 Answers

SOURCE: packard bell Argo C Laptop motherboard EasyNote MZ35

TRY EBAY

Posted on Mar 24, 2008

Geekman
  • 32281 Answers

SOURCE: need to make laptop notebook packard bell dvd region free locked on o1

You can only change the region code up to 4 times then it locks on the last change.
There are some firmware upgrades that can change the drive to region free, if you can screw it up or put in the wrong frmware upgrade then the DVD drive will be a piece on junk.
I suggest you install a region free software that will allow you to play any region DVDs.
Go to www.dvdidle.com to get their Region-Free software, it is not very expensive.

Posted on Nov 24, 2008

freetek
  • 5568 Answers

SOURCE: PACKARD BELL 7521N

To see if they offer a manual for download, you need to get the whole PN and go here:
PB Support
7521n was not recognized.

Posted on Dec 15, 2008

  • 48 Answers

SOURCE: can someone please tell me where the hard drive of Easy one is?

Flip the laptop over and unscrew the cover(s) and you should see the hard drive. It might have a screw or two holding it in. Remember it will be much smaller than a pc hard drive. It is a little bigger in size than a card from a deck of cards.

Posted on Apr 17, 2009

WinstonMeyn
  • 141 Answers

SOURCE: the mouse of my laptop Packard bell is locked. how

On the top of the keyboard you can see a picture of a Hand on a rectangle which should light up press is once , touchpad will be working fine !

Posted on Jul 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Motherboard south bridge solution my compaq laptop


HP/Compaq web site should have all the drivers you need for your computer.

Nov 05, 2013 | PC Laptops

1 Answer

Short circuited laptop motherboard


get a new motherboard that is simplest and most effective

May 29, 2012 | Acer PC Laptops

3 Answers

I have a packard bell r 6512 laptop I lost recovery cd. so I want drivers for the above said laptop. How can I get.


you can to to there old link here --->ftp://ftp.download.packardbell.com/NOTEBOOK/EasyNote%20R6%20series/Driver/xp/

Dec 04, 2010 | Packard Bell PC Laptops

4 Answers

Packard bell easy note tj65 will not power up


the short cable running from the power button to the main board has probably snapped where it passes over the RH hinge. remove the screen surround to gain access to the power on switch area and check. it would seem to be a common fault with the packard bell

Mar 07, 2010 | Acer PC Laptops

1 Answer

The touchpad stopped working on my Packard Bell EasyNote TN65


could be malware infection but before, open and check that touchpad to motherboard interface flex is ok and well plugged in the socket. also uninstall all touchpad drivers, run a malware removal tool then, scan for new hardware..
Regards

Feb 26, 2010 | PC Laptops

1 Answer

I dont know where the hard drive is located on the Packard Bell easy one 1550 notebook


Uner the keyboard is what my diagram says. it also can be mounted just beside the battery so check both locations. wow packard bell is a old computer.. But still good i guess. Rate me I appricate anything above thanks for trying!!

May 14, 2009 | Packard Bell Easy One Silver 2120 Notebook

1 Answer

Packard Bell Easy One Silver monitor problem


Hi there.
You need to be looking at the inverter, this is a very thin circuit board located underneath the screen so you will have to remove the plastic bezel (screen surround) check the connections on that. If the screen is still white look at the inverter itself because there could be a dry joint or the coil has gone, if you are confident with a soldering iron then re-solder all the points on the inverter circuit board and try it again.

Good luck and thanks for using FixYa!!

Mar 11, 2009 | Packard Bell Easy One Silver 2120 Notebook

1 Answer

Have disabled vga adaptor:s have no screen now


you have disabled the vga adapter of your system
now start your system in a safe mode by pressing f8 continuosly during the booting, then restore your computer to the back date

Sep 25, 2008 | Packard Bell Easy One Silver 2120 Notebook

1 Answer

Packard Bell error signals


here is a list of packard bell beep codes with meanings
http://www.uktsupport.co.uk/pb/mb/phnxcode.htm
Hope it helps you

Nov 13, 2007 | Packard Bell Easy One Silver 2101 Notebook

Not finding what you are looking for?
PC Laptops Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Laptops Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a PC Laptop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...