Question about Hilti TE 7-C 120V Rotary Hammer Drill

1 Answer

I have a Hilti Hammer Drill model TE5

I need to know what grease to use in the gear box and where to put it in if it can be done without taking the gear box back apart.
my email is (warren99060@peoplepc.com)

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 79 Answers

Tip - Get a can of PB Blaster from your local hardware store and spray a little into the bit holder. Use a long screwdriver and push down the piston. Hit the switch for a minute, letting it work in. Put a bit in and get to drilling. Unless its old, then the o-rings may just be worn out. That stuff does recondition o-rings too. Lemme know. Please rate me

Posted on Jun 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have Hilte TE5 and can not turn the end to make tbit stay in plce. I think one of the ball bearings in there is missing. Who has paarts formy TE5 ?


In the US you can contact Hilti @ 1-800-879-8000
The easiest way to repair your drill would be to replace the whole chuck. It will just snap on and off.

Sep 19, 2010 | Hilti Hammer Drills

1 Answer

Te70 hilti hammer drill


The TE-70 is permantly lubricated. You would only add lubricant if you took the tool apart. You can add a small amount of grease to the end of your bit occasionally before putting in the chuck. This keeps the chuck parts lubed.

Jul 09, 2010 | Hilti TE 7-C 120V Rotary Hammer Drill

1 Answer

Hilti te5 problems


go to Hilti.com and you can download a breakdown for this tool. Let me know if you need more help with the repair.

Mar 12, 2010 | Hilti Hammer Drills

1 Answer

Hilti te5 motor turning but not driving chuck


While the drill is running grab the chuck and turn it by hand. If you here a grinding noise that tells you the rotor gear is stripped.

Feb 20, 2010 | Hilti Hammer Drills

2 Answers

Grease for hilti te 24


any liquidy grease like lubriplate or milwaukee type Y grease part no. 49-08-5270

Oct 20, 2009 | Hilti TE 7-C 120V Rotary Hammer Drill

2 Answers

DRILL FUNCTION BUT NOISY IN USE


Depending on the type of hammer drill you have, the noise should only be heard when you are applying pressure to the material you are drilling. Some drills have 2 bump plates that cause the hammer action. This is what causes the noise. It kind of sounds like the gears are stripped but the chuck still goes just fine. You do not need to grease this, it will make this noise regardless. However you may want to take a look at the gears and make sure they are ok. You may want to add grease if the old grease is broken down or there is not enough in the gear housing. Larger hammer drills have a piston and actual hammer. Such as the Bosch Bulldog series. If it is this type and there is noise when you are in drill mode there may be more serious problems.

Sep 24, 2009 | Hammer Drills

1 Answer

Slow te5


Bring it in to a factory service center. They will give you an estimate on how much it cost to repair it. Then you can decide to chuck it or not. Also hilti will give you a trade in for your gun if you decide to buy a new one.

Here is a link to find a service center in your area:

http://www.us.hilti.com/holus/modules/home/home_submain.jsp?catname=/subhome/services

Mar 26, 2009 | Hilti TE 7-C 120V Rotary Hammer Drill

1 Answer

I have a Hilti Hammer Drill model TE5 and I need know grease to use in it


the grease is called turmoil grease and is somewhat expensive. This also requires just about complete disassembly of the tool and smoe parts replacement.

Oct 25, 2008 | Hilti TE 7-C 120V Rotary Hammer Drill

Not finding what you are looking for?
Hilti TE 7-C 120V Rotary Hammer Drill Logo

Related Topics:

966 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hilti Hammer Drills Experts

John Trevino

Level 3 Expert

1378 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Phil Rivera

Level 2 Expert

83 Answers

Are you a Hilti Hammer Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...