Question about SATO CL408e Thermal Printer

Open Question

RECALIBRATE MEDIA FOR SATO CL408e

RCALIBRATE LABELS

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

checkitright
  • 1362 Answers

SOURCE: SATO eSeries CL408e driver

here it is

 

 

http://www.satoworldwide.com/our_products/software.asp

Posted on Oct 22, 2007

SOURCE: printer problem

check baud rate on NIC card (pull out NIC), against COM settings on PC. they must match. 9600 usually works

Posted on Jan 14, 2008

  • 52 Answers

SOURCE: my sato cl408e label printer misses printing on

recalibrate the stock.

Posted on Jan 27, 2010

  • 1768 Answers

SOURCE: my network can't detect the new sato cl408e we just purchased.

1.Log into router
2. Verify wireless router name( on the computer) >>> ( on/off)
3.Note router name you are connecting to.
4.. Check the laptop,desktop,printer do ipconfig /all to see current IP addresses.
5. Set the laptop up in the router by WEP KEY or MAC address.
6.Note router name you are connecting to.
7. Move the device about 20ft away and try to log on to the internet.
This is for all routers to set up wirelessly.

Posted on Jun 29, 2010

  • 1 Answer

SOURCE: Hi, Sato CL408e, it starts printing

1) Try to calibrate the printer.
Else
do factory reset ( Press LINE and FEED At same time and switch on the printer.
Else
Change the potentiometer offset (Pitch,print) settings in the front panel.

Rgds
Mohan

Posted on Jan 24, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sato cl408e - printing over perforations. I tried turning the Pitch(all the way to the right) and Offset(all the way to the left), and this helped a little, but still not right. Because of this, when the...


Reset printer sensor threshold setting.

Turn on printer whilst holding down line key untill printer beeps.

Use feed key to step to Gap in display.
Load label plus backing under sensor and not volts reading.
remove labels and place backing only under sensor and note volts reading.
use following formula
High reading + Low reading / 0.5 = Value to use
e.g 2.8 + 1.4 / 0.5 = 2.1.

use result to change value of input using line key once set press feed key to set.

To change label start position use the pitch menu.

Jun 02, 2011 | SATO CL408e Thermal Printer

1 Answer

Hi, Sato CL408e, it starts printing between the labels. The feed is off by about 0.5cm. Any idea on how I can adgust that?


1) Try to calibrate the printer.
Else
do factory reset ( Press LINE and FEED At same time and switch on the printer.
Else
Change the potentiometer offset (Pitch,print) settings in the front panel.

Rgds
Mohan

Jan 21, 2011 | SATO CL408e Thermal Printer

1 Answer

SATO and ZEBRA PRinter Hardware Support


Contact Lancer Labels on 0845 833 0854, they can arrange a service call anywhere in the UK.

Feb 10, 2010 | SATO CL408e Thermal Printer

1 Answer

Outside wind ribbons/labels


sato uses outside wind ribbon and inside label.
you shouldn't have to configure anything as long as the ribbon spindle turns and registers movment

Nov 22, 2008 | SATO CL408e Thermal Printer

1 Answer

Printer Error(Sato Cl 408 e)


PROBLEMA EN AJUSTAR EL CORTE DE LA ETIQUETA, CUANDO LA IMPRESORA SENSA LA ETIQUETA, ESTA QUE CORRIDA HACIA LA PARTE DE ATRAS DEL CABEZAL HACIENDO NECESARIO UN FEED PARA PODER CORTAR LA ETIQUETA


Jul 05, 2008 | SATO CL408e Thermal Printer

2 Answers

Pare parts in India for SATO CL408e printer


can better you to visit SATO website and get the information you wanted

Dec 27, 2007 | SATO CL408e Thermal Printer

1 Answer

Printer problem


check baud rate on NIC card (pull out NIC), against COM settings on PC. they must match. 9600 usually works

May 22, 2007 | SATO CL408e Thermal Printer

Not finding what you are looking for?
SATO CL408e Thermal Printer Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top SATO Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

kbtkbt

Level 2 Expert

67 Answers

pkwc

Level 2 Expert

254 Answers

Are you a SATO Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...