Question about Projection Televisions

1 Answer

My pdp r03u has an error code e01 - Projection Televisions

Posted by on

  • 2 more comments 
  • Anonymous Nov 12, 2008

    I have the same problem. I had an authorized service center check it out in-home and all they could do was tighten the cable connections. That worked for a few weeks and then the problem returned. I called Pioneer and they said the R03U could only be serviced at the factory and they have a flat fee of $500. There has to be a better way.

  • jtsc Dec 10, 2008

    Mine just started the same thing in the last few weeks. It's a Pioneer PDP-R03U 43" display that I've had for a little over 6 years. 


    Recently, it started to not display the inputs on the screen (like showing the feeds from TV, Input 1, 2 and so on and just giving a blank screen. Within another minute or two, it shows a message that just says E01 (in red, in the middle of the screen) and then shuts itself off. 


    Very expensive display and I am very disappointed to be having this kind of issue. 


    I've checked the cables, but I will recheck. It just does not seem worth it any more to get electronics fixed (cost/benefit ratio as opposed to buying a new replacement (with an extra cheap unit- they are giving them away these days...).  


    For the record, I expect about 10 years use out of a TV (and I don't think that's too much too expect).


    Any thoughts on making this unit work?

  • jamiejenson8 Dec 31, 2008

    I have recieved the same error code as well. Has anyone figured out what is causing this problem or how to fix it. Please help!

  • crcarpetrug Jan 28, 2009

    i have the same problem.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

I have a 50" Unit with this same part, I called Pioneer and told them what was happening, they asked me to count the flashes on the monitor power indicater light and when I told them the problem they told me that it was a dry solder weld, I called a tv repair tech and told him what was going on, he had never worked on Plasma Tv's and was very hesitant to start I told him if I just brought in the Media Box and had him check the solder joints how much would he charge he told me to try he wouldnt charge me anything, I jumped on that! he saw a few issues and fixed them, I brought the unit home plugged it into the tv and the tv works just fine!

Posted on Apr 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have pdp 505 ,the s\b light flash for 11 time


thats the error code for an issue with the digital DC Volts. Chances are the digital board will need replacement.

Aug 06, 2011 | Projection Televisions

3 Answers

Pioneer pdp-ro3u pops up E01 then shuts off


reset the device by unpluging the device for somr minutes and then again replug and see if it works.

thanks.

Oct 28, 2008 | Projection Televisions

1 Answer

When you turn it on it might go on then turn off or it might not go on at all the power light blinks won't shut off unless you unplug the TV.j


The blinking LED is the Fault code for your set. Its shutting itself down into protection mode to stop from further damaging itself. Kinda like a fail safety. My fix instruction differ for rear projection than that of PDP or LCD but its the same. Just a dif set up inside the set.

Aug 06, 2010 | Toshiba TP50H50 50" Rear Projection...

1 Answer

Pioneer Plasma


hello have you got a media box if so id check the it for dry joints in the power supply good luck

shaun

Apr 04, 2009 | Pioneer Projection Televisions

1 Answer

I have a pioneer 50 inch plasma model no pdp507xda i need a new screen how much will it cost cheers


part #AWU1316 Pdp Service Panel it is listed as no longer avaible because they do not sell the pdp to the public or non service centers
sorry
scott

Nov 04, 2008 | Pioneer Projection Televisions

1 Answer

My daughter has smashed the screen on my Panasonic PDP-4270XD Plasma TV. How much would it cost to repair?


Sorry to say, you can replace the entire TV cheaper than a new plasma panel as they run about 2000.00

Aug 10, 2008 | Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

661 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...