Question about Black & Decker Tools & Hardware - Others

Open Question

Need schematics for vector/black&decker charger model PKC1097A

Battery charger 30-10 2 /with 80 amp start

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Black and Decker Battery Charger

Fault Codes Meaning of Fault Code F01 Internal Shorted Cell Battery - Cannot be charged. Have battery checked by certified auto service center.
Excessive Load on Battery While Charging - Check load. F02 Bad Battery Connection - Check battery connection.
Battery Voltage Tool Low to Accept Charge - Have battery checked by certified auto service repair. F03 Internal Open Cell - Have battery checked by certified auto service center.
Sulfated Condition - Battery needs to be reconditioned. See manual. F04 Overtime Condition - Battery will not accept a charge after 18 hours of continous charging. Battery may have internal
damage. Have battery checked by certified auto center.

Battery Charge Rate is Set Too Low - Set charger to higher charge rate. See manual. F05 Overheated Condition - Disconnect charger and allow to cool for 30 minutes. Check for ample ventilation. F06 Reverse Polarity F07 Alternator Output is Out of Typical Operation Range

Operation Codes I=I=I=I Battery Reconditioning - (The letters DES will display for the first three seconds) I-I-I-I Alternator Voltage Check OOO Charger Standby FUL Battery Fully Charged

Posted on Nov 20, 2008

  • 52 Answers

SOURCE: I need to replace the 120 volt AC wall adaptor

Here is your link to buy it.
http://www.centurytool.net/5140044_04_Charger_W_Small_Jack_p/5140044-04.htm

Posted on Jan 11, 2009

  • 205 Answers

SOURCE: Black and Decker battery charger does not work.

Open it and look for a fuse, then go buy a new one (my Ryobi charger didn't have a fuse)

Posted on Apr 02, 2009

venexcsd
  • 1185 Answers

SOURCE: Black & Decker 24 volt battery will not hold a

Click on the link below and you will find replacments

You need to work out if the cost of two batteries is cheaper than a deal on a new drill pack


http://www.svcvacuum.com/black_and_decker/black_and_decker_battery.htm

Posted on Jun 01, 2009

  • 20 Answers

SOURCE: My Black and Decker Firestorm 24 volt charger is not working

change batteries, your charger should indicate wheather you battery is good or noot on the pause inbetween blinks.

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my battery charger only go on float charge


If you are saying the charger is staying on the very low side of charge for a dead battery .depending on the type charger you have it may be your battery is too low for your charger to get the dead battery going..sometimes I need to give a completely dead battery a jolt to get it going..if you have or know some one has a jump start type charger that puts out very high amps for starting..have them give it a few min of that high amp charge..if you have a battery where you can take the cals off you should see the cells bubbling...All cells must show some or it is shorted. Just don't let on more the a min or two...good luck

Oct 01, 2014 | Cars & Trucks

1 Answer

How do I start the yamaha riva125cc w/electric start? Do I have to hold the gas or throttle. It's a '94.


Are you actually trying to start the bike with a battery charger switched on and connected to the battery. If so then you are at risk of blowing the whole electrics system battery and charger. Try removing the battery (undo negative lead first please) connect a dedicated motorcycle battery charger to it and allow the battery to reach full power. The charger should have an output of no more than 1 amp. Car chargers will wreck your battery DON'T USE THEM EVER. When the battery is fully charged refit it (positive lead first please) then try to start the bike. You cannot expect a battery charger to give enough cranking current to start a bike it is not designed to do it. NEVER USE A CHARGER WITH A JUMP START FUNCTION OR TRY TO JUMP START USING A CAR BATTERY LINKED TO YOUR BIKE. Both of these will fry your battery and possibly make it explode. Good luck

Sep 24, 2014 | Motorcycles

1 Answer

How many amps to charge a car battery?


most chargers these days regulate the amperage as the battery charges. My Motomaster charger starts off at 16 amps on a depleted or low battery and goes down to 5 amps once fully charged. Battery maintainers put out about 2 amps.

Jun 12, 2014 | Vector Black And Decker High Frequency...

1 Answer

How do I use a battery charger to charge my dead battery on a 2001 camaro


The red clamp on the charger goes to the + sign on the battery. The black goes to the -. I you want a deep charge(best) set the charger on 2 amps and run it for 8 to 12 hours. If you need to get the car started, set the charger on 225 amps for just a couple of minutes. Start the car while it is on..2 amps can charge forever. 20 amps for 30 minutes. 30 to 40 amps for 15 minutes. 225 amps for five minutes..DO NOT charge 20+ amps for hours. It will kill the battery

May 12, 2014 | Cars & Trucks

2 Answers

How do you hook up amp meter for battery charger


DO NOT CONNECT IT to both poles + - !!! the amp meter have very small internal Ressistance, it blows of :) Connect it like in the picture d640b1d6-15c8-40ff-9dc1-eac0eb3b2a1f.png

Apr 16, 2014 | Cars & Trucks

1 Answer

Power cord vector start it VEC012


Here's a link to the power charger I needed, its a Black & Decker Replacement A/C Charger. I ordered it at the following:
http://www.amazon.com/Black-Decker-5140045-42-Replacement-Charger/dp/B002V6VIZW/ref=sr_1_1?s=hi&ie=UTF8&qid=1445366598&sr=1-1&keywords=Black+%26+Decker+%235140045-42+Replacement+A%2FC+Charger

Feb 15, 2014 | JUMP START SYSTEM

1 Answer

I have a homelite 720 generator but cant fingd the instruction manual and i need to know if the charger leads only charge a battery or can be used as jump leads i know this might sound stupid but i wo


I can't find any reference to a Homelite model 720 generator but most battery charging systems do not supply enough amps to run a car starter. Battery chargers usually work in the two (trickle) to ten amp range. Car starters need way more amps to have enough power to turn an engine over, depending on the size and number of cylinders in the motor. Some chargers have a switch with a 60 amp 'start' position to help the battery turn the motor over, but without that there is little chance the charger side of your generator will supply enough amps to help your battery.

Feb 21, 2012 | Cars & Trucks

1 Answer

I NEED A CHARGER FOR THE VECTOR189 CAN YOU HELP???


In March, 2006, Black & Decker purchased Vector Products, Inc. Since the acquisition, Black & Decker has assumed the manufacturing of all Vector products. For customer service and warranty information for Vector products, please contact Black & Decker Customer Service.

Oct 24, 2010 | Vector Camping, Backpacking & Hiking

2 Answers

I need a replacement charger cord for the Vector 3 Million. I live in Birmingham, MI. Where can I order this from?


In March, 2006, Black & Decker purchased Vector Products, Inc. Since the acquisition, Black & Decker has assumed the manufacturing of all Vector products. For customer service and warranty information for Vector products, please contact Black & Decker Customer Service.

Oct 01, 2010 | Vector 3 Million Candlepower Rechargeable...

1 Answer

I need a phone # to order a charger for a vector sport spot (vec139y) thanks. Avery Moore 919-369-2744 or 919-291-0479


In March, 2006, Black & Decker purchased Vector Products, Inc. Since the acquisition, Black & Decker has assumed the manufacturing of all Vector products. For customer service and warranty information for Vector products, please contact Black & Decker Customer Service.

Sep 27, 2010 | Camping, Backpacking & Hiking

Not finding what you are looking for?
Tools & Hardware - Others Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Black & Decker Tools & Hardware - Others Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Gil Shultz

Level 3 Expert

3368 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Black & Decker Tool and Hardware - Other Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...