Error Code: F-20

what's f24 code? - Kenmore Elite HE3 Washing Machine ...

https://www.ifixit.com/Answers/View/85549/what's+f24+code

iFixitAug 21, 2015 - Aiman, The F24 error code indicates a water temperature sensor reading that is ... The Kenmore Elite HE3 is a washing machine by Kenmore.

F24 Error Code on My Kenmore Washer ' eHow

www.ehow.com > Home

F24 Error Code on My Kenmore Washer. Kenmore washing machines have several high-tech features, such as a stain treatment option, reduced energy and ...

Kenmore HE2 Plus Front Load Washer F24 error code ...

www.fixya.com > ... > HE2 > Kenmore HE2 Plus Front Load Washer

...error code F24 I have a Kenmore HE2T washer and I keep getting an F24 error on it.. I have no idea what is means can't find the manual help!!! The "F24" error ...

I have a Kenmore HE2T error code F24 - Fixya

www.fixya.com/support/t3608391-kenmore_he2t_error_code_f24

Dec 9, 2009 - Posted on Dec 09, 2009.

Error F20 indicates lack of water entering the machine.

Read more: http://www.ehow.com/search.html?s=+Kenmore+HE2+Plus+Front+Load+Washer++F20+error+code&skin=home&t=all#ixzz2qLeZJpIO

The F33 error code indicates a pump drive system error. If the pump ohms out correctly & the harness is secure I recommend replacing the CCU (central control unit). Remember to disconnect power to the washer before attempting access. could be a bad pump or loose wire connections. good-day !

Thanks for choosing FixYa and welcome to the site. Have you tried unplugging the machine yet to reset it? Are you getting any error codes? Also, if I may, what does ': mean please? Is this a code?

Yes. Way too much for 20 year old machines.

I would try to find out what the "F-01" means but if you need to replace circuit board they normal are easy to "unplug and replug" wires. But SEARS tech's would be best to repair. If can't find a source to tell you what F code stands for , call SEARS service and when he diagnoses problem you could see or ask him how to replace my tech is helpful that way, then it only cost the "service casll" rate and not hte return part replacement cost also

I have same machine and manual says, "F20" on display (water inlet problem - no water or insufficient water supply). Select STOP twice to cancel the cycle. Unplug washer or disconnect power. Check the following. Are water faucets completely turned on? Are screens at inlet hose connection to washer clogged? Are water inlet hoses kinked? Are water inlet hoses frozen? Plug in washer or reconnect power. Re select cycle and press START. if the problem remains, call for service.

Your washer needs to be serviced by a professional. That error code means there is a communication error between the Control Unit and the EEPROM; the CCU needs to be replaced. Check to see if your product is still under warranty.

Refer to page 2 of this service manual:

https://www.servicematters.com/docs/wiring/Tech%20Sheet%20-%208540259.pdf

You probably have this solved by now but for others who read this as I did.............
F-20 means
“F20” on display
(Water Inlet Problem—no water or insufficient
water supply) Select PAUSE/CANCEL twice to cancel the cycle
Unplug washer or disconnect power. Check the following: Are water faucets completely turned on?
Are screens at inlet hose connection to washer
clogged? Are water inlet hoses kinked? Are water inlet hoses frozen?
Hope this helps everyone else as it did me, thanks

"F21" is a Long Drain error. This occurs when the drain time exceeds 8 minutes. You will need to remove the bottom panel under the door by removing the two screws at the bottom edge of the panel. First, check the electrical connections to the drain pump and make sure the pump is running. Check the drain pump filter to make sure it is not clogged with debris. This is a very common problem. HINT: Before removing the drain pump filter, pull the drain hoses from the standpipe at the wall and use a shop vac to pull a vacuum on the drain hose to get rid of all residual water from the pump and drain lines. This is also a good way to get rid of minor clogs. If you do not own a shop vac, be prepared to lay down some old towels and soak up some water. There's quite a bit of residual water in the wash tub and lines (this is normal). In addition, check your drain hoses to make sure they are not clogged or kinked. If you check everything and still have the error code, replace the drain pump. Replacement parts can be found at searspartsdirect.com and repairclinic.com. Just type in your model number in the search menu. I hope this helps you. If you require further assistance, please let me know.