Question about ITT Night Quest 220

Open Question

ITT Night mariner 260 Gen 3

Insruction manual needed

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 298 Answers

SOURCE: Repairs to ITT Night Mariner 160

ITT Night Vision
7635 Plantation Road
Roanoke, VA 24019
Telephone: 540-563-0371
Fax: 540-366-9015
Toll free: 800-448-8678
General email:
nv.orderadmin@itt.com
Call For Suppliers
Warranty Repair and Technical Support Toll free: 1-800-360-6054
Fax: 540-362-7400
email: nvwarranty@itt.com
Company Links ITT
ITT Defense and Electronics

Posted on Dec 19, 2007

magoo23
  • 22 Answers

SOURCE: ITT night mariner 160

My advice ,if i were you, would be to leave the batteries in for a day and leave your unit turned on. either leave the cap on, or put it in a closet and see if it works better. The new AAA batteries should be fine i'm sure you have how to put the four in correct, and yes they are all that's needed. But leaving your unit on for the day will do a few things. First, it puts a current through all of the working components, i.e. light gathering elements and your infrared components. They may "wake up" from being on and they may not. But at the very worst you are only out the cost of four triple A's.

Posted on May 06, 2008

  • 18 Answers

SOURCE: ITT Night Mariner 160

www.nightvision.com.au can repair but parts not easy to get

Posted on May 31, 2008

SOURCE: itt night quest 150

Sounds like the image tube may have shifted in its mounting? This sometimes occures when the night vision has been subjected to an impact or dropped sometime in its life. Repair is not cost effective for a 150 / Gen2.

Posted on Sep 26, 2008

  • 75 Answers

SOURCE: does anybody know what type of battery The ITT night quest 220 ni

I'm pretty sure that your unit uses the 3V cr123 Lithium battery. You can get it at RadioShack. You can always take it down to radioshack and pretty quick you will find the correct batt.for the unit. Do not use rechargeable batts!

Posted on Apr 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed batterys no power black eye nothing


How long have you had this ITT Night Mariner 160 NV monocular? Sorry, it needs to taken a part and trouble shoot the electronic components and image intensifier tube. stewbison. If I had my shop set up but I sold all of my electronic test equipment. Contact ITT and ask them what to do. stewbison

May 03, 2011 | ITT Night Mariner 160 Monocular

1 Answer

Repairs to ITT Night Mariner 160


ITT Night Vision
7635 Plantation Road
Roanoke, VA 24019
Telephone: 540-563-0371
Fax: 540-366-9015
Toll free: 800-448-8678
General email:
nv.orderadmin@itt.com
Call For Suppliers
Warranty Repair and Technical Support Toll free: 1-800-360-6054
Fax: 540-362-7400
email: nvwarranty@itt.com
Company Links ITT
ITT Defense and Electronics

Dec 19, 2007 | ITT Night Mariner 160 Monocular

1 Answer

Will not power on


Hello, these ITT Night Mariner 160 monocular are almost impossible to work on. To make them water proof every joint, hole, cap are epoxyed on. Check the internet and look for companies that manufacture materials that will desolve epoxy cement and even better stuff is that it makes the epoxy really soft for it can be removed. Sorry dude I couldn't be more help. stewbison

Mar 30, 2011 | ITT Night Mariner 160 Monocular

1 Answer

Left a pair of PVS7B/D's on with the pinhole lens cap in place for about 16 hours by mistake, now I see a "ghosted" permanent image superimposed over my real time image. What does this indicate?


It's called time exposure or flash over. What happen is the infiltrating light through the pen hole and a long duration will burn shadows into the micro channel plate in the generation 3 image intensifier tube.

These expensive image tubes can be repaired. Contact Itt inc or Vard Inc in Garland, TX. That about it unless you want to buy a new gen 3 image tube. Maybe $1500+. I would call around to other Night Vision Optica companies and see if the have a used gen 3 image tube. There quit a few companies in the USA that work on NV devise. Also, contact ITT and ask them they repair image tubes, maybe! stewbison

Jan 20, 2011 | Optics

1 Answer

Hello i dont necessarily have a problem with my itt 190. I am actually researchujng the nvg before i decide to purchase it. I know its a gen 3 but know little else. Iam under the impression it is a...


electronic components; resistor, capacitor, transistor, processor, switches, wire, all component have to meet or exceed those standards set by the Military. When these component come together to make ccfl, inverter, voltage multiplier, controller that they have to meet standards set by the US Military RD. Those standard are stiff. Wonder why they didn't throw the M16 or M4 in a junk pile. junk.
The image are made by ITT liton, Vard In, Photo-tonic, etc. These companies apply for military contracts in which there manufactured item will have to meet Military standards. This companies are American. Maybe with the exception Photo-tonic it has linage to Europe--Belgium.

Vard Inc made the 1st generation PVS2 Star Light Scope in 1962 which was first used in Vietnam successfully. There were other NV devise big and bulky. Back in the 50's the Army had rifle mount scope, it took three soldier to operate it. You couldn't sneak up on blind rat with it....

I used PVS2 in Vietnam and it save my *** a few times. As you know being in the military everything you carry has to be light.

When I was in Vietnam and southeast Asia for 34 months. One learned in a hurry to drop stuff that you really don't need, gas masked, sleeping mat, ratios, etc.etc... In Vietnam i carry 18 clips/50 round bagged of ammo for M2 carbine, three hand grenades, one ***** trap grenade. two ***** trap AK47 clips. I used indigenous pack, poncho line, indigenous poncho, five plastic bag of rice with beef and chicken bullion (from home). Tabasco sauce. four canteen of water, and one 3/4gal bag of water. Sometime I worn Vietnamese cloths, loose fitting black silky pants and linen shirt, Cooley hat, Uncle HO sandals. and sleep in the air, mud, on the ground, up against a tree or in a water fill bomb crater.

I carry what I needed, not what the Army want me carry. I got in a lot of trouble but I prevailed in those adversaries. I hope I answer all your questions. stewbison

Dec 23, 2010 | ITT Night Mariner 190

1 Answer

Hi, I have the night mariner 250 model (Gen 2?), when turning it on it shows the low battery indicator (red) light flashing and then switches off after approx. 6 seconds. It does this all the time, even...


The problem could be caused by dirty battery contacts or faulty capacitor on power supply board.

I suggest cleaning the battery terminals with iso-propanol alcohol and fine emery paper.

If this doesn't work, you really should take it to a repair/service centre.

Mar 23, 2009 | ITT Optics

2 Answers

Itt night quest 150


Not sure if this applies, but this is on the Morovision site: http://www.morovision.com/faqs.htm Because of the manufacturing processes, all night vision image tubes will have different cosmetics such as small spots or specs, photocathode coloring, or a chicken wire effect from the microchannel plate. Most cosmetics are only noticed during viewing in high light situations such as viewing with the daylight filter on in a lit room. Most cosmetic blemishes are not noticeable during normal nighttime operation but may still be seen to some degree in certain situations. These cosmetics in no way effect the performance of the image tube and do not decrease the ability to perform nighttime tasks.

Jul 11, 2008 | ITT Night Mariner 160 Monocular

1 Answer

Installed new batteries and it still will not work


replace with new battery and retest. this unit has a itt 2nd gen tube with an encapsuled power supply next to the tube the power supply is probably faulty the two sides of this nv are also siliconed together making it a difficult unit to dissasemble for testing but i have done this model before

Apr 29, 2008 | ITT Night Mariner 160 Monocular

Not finding what you are looking for?
ITT Night Quest 220 Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top ITT Optics Experts

Joe Lalumia aka...
Joe Lalumia aka...

Level 3 Expert

3186 Answers

kakima

Level 3 Expert

102366 Answers

Mark Campeau

Level 1 Expert

44 Answers

Are you an ITT Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...