Question about Sharp Aquos LC-32G4U 32 in. HD-Ready LCD Television
My tv just lost all its color. i don't think i have reset anything because upon switching it back on after an hour, the display is already in black and white. no amount of resetting the picture set up have turned the color back on. what do i do?
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Clean screen
I used the Monster "Screenclean" kit, which left a film on my screen. I am not happy with it. Any suggestions on a different product which will remove the film?
Posted on Jun 06, 2008
SOURCE: LC-37AF3X Sharp Aquos KCD TV
If the TV goes in standby, then it is in protection mode.
Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
Try first leaving the TV power cord unplugged for some times, let say one hour or so.
The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.
1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.
2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.
If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.
If you are in situation 2 , then there is an internal fault.
If under warranty contact the manufacturer ringing the number on the user manual
If you want to repair at your own expenses, just locate any good qualified repairer.
If you want to DIY you find parts here,
All: Appliance parts, electronics parts & more from PartStore.com
Encompass Parts Distribution
LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |
On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem
On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.
On Rear Projection : check lamp, lamp ballast, power board, and convergence.
On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.
Posted on May 05, 2009
SOURCE: Sharp Aquos Resolution
According to the manual for the TV, you need to change the resolution on the computer itself first.
The computer resolution should be 1024 X 768 at 60Hz or 1360 X 768 at 60Hz.
After the adjustment made on the laptop, then try the resolution change option.
Posted on Jun 12, 2009
I'm happy with:
although I found this setup but haven't tried it yet
colour +50 (review I found didn't say + or -. Try both
Posted on Sep 21, 2009
Tips for a great answer:
Jan 28, 2016 | Sharp aquos 52 in lcd 1080p aquos 52...
Oct 20, 2015 | Sharp Televison & Video
Aug 13, 2015 | Sharp Aquos Televison & Video
Jan 29, 2015 | Sharp Televison & Video
Mar 21, 2011 | Sharp LC-32SB24U 32 in. LCD TV
Apr 18, 2010 | Sharp Aquos LC-30HV4U 30 in. LCD HDTV
Mar 05, 2010 | Sharp Aquos LC-42D62U 42 in. LCD HDTV
Jan 11, 2009 | Sharp LC-42D64U 42 in. LCD HDTV
653 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: