Question about GE Telephone

Open Question

I have a GE telephone model 29385GE2-A and the display is not displaying properly. Can it be fixed?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 62 Answers

SOURCE: Display on handset does not display any info!

The display could be bad or the didplay driver could be bad or it could be a simple wiring problem if you're lucky. Try pressing around the edges of the display to see if anything appears (press firmly but not so hard as to break anything). If you are mechanically inclined, open up the handset and connect the battery so the handset works. Normally the display is connected to the phone circuit board by a ribbon cable and frequently there is a tiny "edge card connector". If present, make sure the connector is plugged in completely. Watching the display, try pressing on the ribbon cable where it attaches to the display and to the circuit board. If anything appears, keep trying to isolate the problem.

I recently had this same problem with a Sony handset but I was not able to find anything as I just described and I ended up replacing the handset with a new one of the same model. Good places to look for a replacement are eBay and Amazon.

Posted on Nov 13, 2008

Ad
mwit465
  • 76 Answers

SOURCE: GE 2.4 GHz cordless telephone problem

Hi there, maybe I can help;
Is the phone base plugged into an switched outlet and is the switch off?

Let me know if I helped

Posted on Jan 06, 2009

  • 1 Answer

SOURCE: I have a GE model #28021ee2a and can not read the display

Handset needs registration go to the base and hold the cordless near it and hold down the page button till cordless beeps. Hope this helps.

Posted on May 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sometimes notebook display flickers and goes stand by


it shows the display drivers does not load properly, re-installation of video driver may solve the issue

Jan 11, 2013 | Computers & Internet

1 Answer

I put new batteries in my At&T cordless phones and I am getting a message on phone screen T23 PD


To register a handset to your telephone base
Make sure the handset battery is installed and charged properly. You have to enter a 15-digit telephone base ID to register the handset to the telephone base.

To find the telephone base ID and register the handset:

1. On the telephone base, press the MENU softkey when in idle mode to enter the feature menu. Press the or softkey to scroll to the DISPLAY BASE-ID menu, then press the OK softkey. The telephone base ID will be displayed.

2. On the handset, use the keypad buttons to enter the telephone base ID and press the OK softkey.
Press the softkey to move the cursor.

3. The handset will first display PLEASE WAIT!!, then T23 PD followed by SEARCHING FOR BASE. The screen will finally display HANDSET X when the registration is successful.
NOTES:

1. If the registration is not successful, the display will show NO BASE SUBSCRIPTION. Try the registration process again.

2. If an incorrect base ID is entered, the base ID will disappear and ENTER BASE ID will be displayed.

In case of a problem or clarification or my solution was insufficient, don't hesitate to post me a reply.

If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Jun 09, 2011 | Cell Phones

1 Answer

Need to find manual for a multi memory GE speakerphone, model # 29385GE2-A


http://www.home-electronics.net/USER-GUIDES/29385_DOM_ES_CD_IB.pdf

Sep 15, 2010 | General Electric Lands Phones

1 Answer

Does the display on my phone suppose lite when a call is


Yes! but some reasons if the battery remaining is too low, the telephone itself saves the battery for emergency purposes so that's why it wont lite-up.

Sep 30, 2009 | Sport & Outdoor - Others

1 Answer

I have a GE model #28021ee2a and can not read the display


Handset needs registration go to the base and hold the cordless near it and hold down the page button till cordless beeps. Hope this helps.

Mar 31, 2009 | Uniden Cordless Phone

2 Answers

Handset display reads "searching". No dial tone. No response.


I am sure you have solved this problem by now. For others who might face the same problem...just unplug the batterry of the handset and plug it in..wow it works!!:))

Jan 20, 2009 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

GE 2.4 GHz cordless telephone problem


Hi there, maybe I can help;
Is the phone base plugged into an switched outlet and is the switch off?

Let me know if I helped

Jan 06, 2009 | GE 21008GE2 Dual-Handset Cordless...

1 Answer

AREA CODE


Just purchased the GE 25922 today. Looks like you can skip (ignore) the option to enter an area code.

United States' Area Codes are three-digit numbers. If the phone 'requires' entering a number you can use any three digit number. The purpose of this option is to display a local telephone number with only the 7 digits.

Example:
603 - 123 - 4567
'603' is the area code
123-4567 is the 7-digit local number.

If the area code option is programmed to '603', then if that number called '123-4567' would display on the Caller ID display.
Which now reminds me: you would need to also subscribe to Caller ID with the Telephone Company for the numberic display to occur.

Oct 27, 2007 | GE 25922 Cordless Phone

2 Answers

Caller ID Problem on the GE2811 Twin cordless phone system


How to get the caller ID to work on the additional GE DECT phone handsets. You must follow these steps in the exact order :
#1 - unplug the base phone
#2 - unplug the telephone line from the base phone
#3 - remove the battery packs from the phones
#4 - wait 10 minutes. reverse the order when assembling. Put battery packs in phones, put the telephone line back in the base phone and lastly plug all phones back in.
It takes about another 10 minutes after that before all phone handsets start recognizing caller ID.

Oct 23, 2007 | GE 28111 Cordless Phone

Not finding what you are looking for?
GE Telephone Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Computer Repairing
Computer Repairing

Level 3 Expert

14641 Answers

Dudeman321

Level 2 Expert

230 Answers

Are you a GE Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...