Question about GE Washing Machines

Open Question

How do you enter diagnostic mode for ge model whdvh626fww washer

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: GE ADORA model WHDVH626FWW

you have to clean out the filter on the bottom by removing the lower panel and twisting the cap... careful lots of water comes out but will work great after

Posted on Dec 13, 2007

Ad
  • 3422 Answers

SOURCE: Ge Adora front load washer not working

Hi,

I don't know how you could have got it into diagnostics mode by accident - - but here's how it goes . Hit the power button until there is NO display . Unplug and wait a minimum of 30 seconds , plug back in and within 30 seconds hit SIGNAL button then DELAY START button then SIGNAL button again then DELAY START button again. door should lock and display t01 It is now in test mode . There are 14 different test it can run through in this mode , but all we are trying to do is check for error codes now and maybe get you back to normal, So turn the knob one click clockwise and hit the START/PAUSE button and see if any error codes come up. To exit the diagnostic mode - hit signal button then delay start button then signal button then delay start button and you are out of service test mode and back to normal

Posted on Sep 30, 2008

  • 2 Answers

SOURCE: Front loading ge washer won't drain?

Similar problem fixed in less than 5 minutes. Here's a post that was very helpful. http://www.foobert.com/blog/2007/04/02/ge-adora-front-loading-washer-does-not-drain/
There's a trap located under the front panel (3 screws) I undid the filter and pulled out 21 coins, 2 buttons, a 'letter h', zipper parts, a broach, and a whole lot of lint.

My wife said that the unit never got the clothes so dry afterwords, she said the almost didnt need to throw the clothes in the dryer.

NOTE: Have a ton of towels ready, and if you can fit a bucket or dish under the filter, go slow and steady. I opened it up and had several gallons all over the floor!

Posted on Jun 04, 2009

  • 1 Answer

SOURCE: washing machine won't turn back and forth

Most likely your drive belt has slipped off. Open up the back of teh washer and see if the drive belt has slipped off and ease it back on with a screwdriver.

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where would i get a drum bearing for my GE WHDVH626FWW, or the part number would be?


Try www.vvapplianceparts.com and type in your model number. You will get a complete picture breakdown of the parts with prices.

Mar 15, 2016 | GE Washing Machines

1 Answer

I have a GE front loader washer model # WHDVH626FWW inner drum making loud thumping noise while washing and spinning


check your owners manual for warranty on inner tub and seal warranty parts may be covered in some cases but labor may not be....

Jan 27, 2011 | Washing Machines

2 Answers

GE front load washer wont start model #WHDVH626FWW


there is a chance that your door lock has failed

Feb 06, 2010 | GE WSXH208A Front Load Washer

1 Answer

Washing machine won't turn back and forth


Most likely your drive belt has slipped off. Open up the back of teh washer and see if the drive belt has slipped off and ease it back on with a screwdriver.

Jun 29, 2009 | GE WSXH208A Front Load Washer

1 Answer

I need a door boot for age washer model whdvh626fww


just enter the model number and the brand in the following link and you can choose any spare part for your model.all the best.

www.espares.co.uk

Jan 13, 2009 | GE Energy Star 3.7 IEC Cu. Ft. Front Load...

3 Answers

A problem has been detected with this unit i need know how to enter my Service Mode Diagnostics


I'll email you a few pages out of a service manual for a WPGT9360 (closest I could find to your model number) hope this helps.

Nov 12, 2008 | GE Profile Harmony WPGT9360E 4.0 Cu. Ft....

3 Answers

Ge Adora front load washer not working


Hi,

I don't know how you could have got it into diagnostics mode by accident - - but here's how it goes . Hit the power button until there is NO display . Unplug and wait a minimum of 30 seconds , plug back in and within 30 seconds hit SIGNAL button then DELAY START button then SIGNAL button again then DELAY START button again. door should lock and display t01 It is now in test mode . There are 14 different test it can run through in this mode , but all we are trying to do is check for error codes now and maybe get you back to normal, So turn the knob one click clockwise and hit the START/PAUSE button and see if any error codes come up. To exit the diagnostic mode - hit signal button then delay start button then signal button then delay start button and you are out of service test mode and back to normal

Sep 30, 2008 | GE Energy Star 3.7 IEC Cu. Ft. Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

673 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...