Question about Onkyo DV-CP500 Multi-disc DVD Player

3 Answers

Re: Onkyo DV-CP500 DVD player stuck in standby mode (by 7 users)

Hello,

I hve this DVD Player stuck in Standby Mode.

You post the solution:

Bad caps in the power supply is causing this. C17 (10v,470uf), C17,c14 (10v,1000uf) and C18 (10v,470uf). Replace with same capacitance values but 25 volt rating 85 C. Just fixed mine half hour ago works great.
Comment by tt500pilot, posted on Jan 22, 2008 ooops meant C7 (10v, 470uf) NOT C17.

====================================

I am not clear on this solution.

Can you please re-specify. Do I just swap out the 3 capacitors?

Thank You!

Sincerely,

Dr. John V. Jaskolski
jjaskolski@wi.rr.com


Posted by on

  • Anonymous Feb 15, 2009

    Onkyo DV-CP500 DVD player stuck in standby mode

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

Hi Yes, sorry just saw this comment. Swap out C7, C17 and C18 in the power supply. Also I would check if you are getting 9Volts to the motor control IC's pin 7 coming off of C005 on the Mechanism Board which is under the unit. The hole for the C005 cap was drilled into a very narrow section of the circuit board and has marginal connection at best.. mine stopped working because of this 6 months after I fixed the power supply.

Posted on Apr 12, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I greatly appreciate the advice -- it is folks like you that make it wonderful for the rest of us without the troubleshooting skills. I can identify and solder, but finding the problem is not my strong suit.

In any event, I replaced the caps in question, and I still have the blinking standy problem. Any ideas on other places to look?

Thanks again,
R

Posted on Jun 06, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Replace all of the 470uF @ 10v & 1000uF @ 10v: C7, C14, C16, C17, C18

Posted on Aug 04, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No sound from new Pioneer DVD player


try resetting defaults
Place DVD player in standby mode
Push in the stop button on the hardware unit and keep pushed in
Push in Standby button on the remote provide while doing the above
Then put into standby mode again insert your DVD and see if it changes.
All Happiness

Apr 08, 2010 | Pioneer DV-333 DVD Player

Tip

Pioneer DVD-400V HDMI Reset Model: Pioneer DVD-400V To switch your Pioneer...


Pioneer DVD-400V HDMI Reset

Model: Pioneer DVD-400V

c552e45.jpg


41457bd.jpg

To switch your Pioneer DV-400V DVD player back to an interlaced video mode after selecting a progressive scan mode and losing picture, follow these steps:

  1. Switch everything off.
  2. Switch the player to standby.
  3. Press and hold the Standy/ON button while pressing the |<< button.
This resets your Pioneer DVD-400V player HDMI output format to 480p.

I hope that helps.
_____________________________________
Pioneer DVD-400V Manual Download
Pioneer DVD-400V Interlace Reset

on Jun 06, 2010 | Pioneer DV-400V DVD Player

Tip

Pioneer DVD-400V Interlace Reset To switch your Pioneer DV-400V DVD player...


Pioneer DVD-400V Interlace Reset

ee72d93.jpg

df1c038.jpg

To switch your Pioneer DV-400V DVD player back to an interlaced video mode after selecting a progressive scan mode and loosing picture, follow these steps:

  1. Switch everything off.
  2. Reconnect using the supplied video cable (standard RCA Red White & Yellow).
  3. Switch the player to standby.
  4. Press and hold the Standy/ON button while pressing the |<< button.
This resets your player to default video output, allowing you to reconfigure your HDMI settings to 1080i, and then reconnect your HDMI cable.

I hope that helps.
_____________________________________
Pioneer DVD-400V Manual Download
Pioneer DVD-400V HDMI Reset

on Jun 06, 2010 | Pioneer DV-400V DVD Player

1 Answer

Onkyo cp500 standby light blinking not turning on


Seems like a manufacturing defect with the way C005 on the Mechanism Control Board was mounted. The positive lead hole on the circuit board for this electrolytic capacitor was drilled into a land that was too narrow for the lead size. The result is no +B to the motor control IC's(LB1641's) on this board. Jumper with a suitable wire from the positive lead on C005 to pin 7 or 8 of the LB1641. This fix obviously assume you know how to take the unit apart (really very simple really if you look at the unit carefully). The board is accessible underneath the entire mechanism.

Dec 31, 2008 | Onkyo DV-CP500 Multi-disc DVD Player

1 Answer

Onkyo DV-SP301 DVD player stuck in standy mode


Had an Onkyo DV-SP301 that would only intermittently come out of standby. Found faulty resistor R2 on the power supply board (board ORTP-865), it was nominally 5600 ohms, measured much higher. This after checking most p/s caps! R2 runs warm when unit is in standby, so you may want to replace with a higher power rated resistor. I used same rating but 10 k ohm instead, worked fine then.

Nov 28, 2008 | Onkyo DV-SP301 DVD Player

2 Answers

Stuck on Standby


Do a hard reset. Unplug it from the socket, the DVD and leave disconnected for 4 hours. This may or may not help, but it is a necessary step to restore all internal software codes to their factory settings.


Hope this may help;

Regards,
VOTIT

DON'T FORGET TO RATE;

Aug 28, 2008 | JVC XV-523 DVD Player

1 Answer

Remote control via RI terminal on Onkyo Receiver


Not sure I can solve, but maybe help. I am having a similiar problem. However, make sure you Analog Audio (RCA type) cable are connected even if using Digital connection between the two. They use those cable to send the Commands (Mentioned in the documentation).
If you did get yours to work, please give me a hint... I upgraded mine from a 603 to a 701 and haven't been able to get it to work since.

Jan 20, 2008 | Onkyo DV-SP800 DVD Player

2 Answers

DVD player stuck in standby mode


Bad caps in the power supply is causing this. C17 (10v,470uf), C17,c14 (10v,1000uf) and C18 (10v,470uf). Replace with same capacitance values but 25 volt rating 85 C. Just fixed mine half hour ago works great.

May 27, 2007 | Onkyo DV-CP500 Multi-disc DVD Player

Not finding what you are looking for?
Onkyo DV-CP500 Multi-disc DVD Player Logo

1,237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Onkyo Televison & Video Experts

sonic boom...
sonic boom...

Level 3 Expert

1557 Answers

The Knight
The Knight

Level 3 Expert

72670 Answers

Cindy Wells

Level 3 Expert

4954 Answers

Are you an Onkyo Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...