Question about Exercise & Fitness

1 Answer

I have an E-4 sign coming up on the treadmill. I still dont have a clue how to calibrate it or anything. i bought it over the internet and there was no instruction manual that came with it. i really need some help. simple guidance is needed please.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 12,223 Answers

Dear Sir:
This is guide for software calibration in Horizon. Please see under your Hood for motor the instruction for step in calibration.
Turn the treadmill power to "On." Place the safety key in its place on the treadmill console.


  • 2 Simultaneously press and hold the incline "+" and speed "-" buttons for approximately five seconds: The console will beep and display the software version in either the "Time" window or the "Calories/Elevation" window.
  • 3 Press "Start" and allow the running belt to begin moving. The belt should start at 0.5 mph. If this speed is not the speed your treadmill starts at, adjust the speed cube screw located under the control board. Turn the screw to slowly to the right to increase the speed or slowly to the left to decrease the speed.
  • 4 Verify this speed is correct by counting the running belt revolutions per minute. At 0.5 mph, the running belt should make four revolutions in a minute for the Alpine and Advance 500 models and four-and-a-half revolutions for all other models.
  • 5 Press and hold the "Stop" button for three seconds to exit the engineering menu.
  • sincerely. God bless you.

    ernesto cuadra
    managua, nicaragua. c.a

    Posted on Feb 17, 2012

    Ad

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Ad

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    I have recently installed treadmill motor brushes but now treadmill is not calibrating,calibration takes start and when calibration comes to check the slow speed it stuck there and keep calibrating it


    Hi There, Please check that you have the small feedback connectors snug and proper. Some treads have them on a front or rear roller and some also have a motor feedback. Or - Try to power down and back up and try to run treadmill normally, not in cal mode, and see if the unit responds to your speed selections correctly. During "calibrations" the upper board (usually) is looking for a specific feedback signal, if it cannot be found it usually stops the tread, but in cal mode it may sit there waiting for it's feedback sweet-spot before continuing. What make, year and model of tread?

    Jun 02, 2016 | Exercise & Fitness

    1 Answer

    HELP! MY TREADMILL WILL AUTOMATICALLY CHANGE SPEEDS TO THE HIGHEST SPEED EVER. ITS INCREDIBLY TERRIFYING!


    please RUN the software calibration inmediately, for easy diagnose and fix it. However adjust the speed sensor, clean it, test for open or fraulty, tight the connector very well.

    God bless youef3bfe4e-a769-4987-8895-a74c14a58a42.gif

    Jun 06, 2013 | Epic Exercise & Fitness

    1 Answer

    Proform power 995 treadmill incline button not responding after initial calibration


    I suggest to RUN again the software calibration, and read carefully your instr. manual for to remember anything
    However see the diagram attached, and lube the gear, shaft of the elevation motor, and tight any connectors or plug ,clean it.
    God bless you
    11_26_2012_5_55_00_pm.jpg

    Nov 25, 2012 | Proform Power 995 Treadmill

    1 Answer

    I have a T85 Treadmill and the running platform is stuck in the highest position. A message on the display says 'check Transmitter'. Is there anything I can do to fix it?


    PLeae RUN the software calibration for troubleshooting go under the HOOD motor and read the instruction steps, or go to instr. manual in how to enter in the s.calibration and fix it.

    However you can measure the input voltage elevation motor, and lube the shafte, gear, see the photo and diagram attached.
    God bless you
    11_19_2012_4_29_11_pm.jpg11_19_2012_4_30_33_pm.jpg

    Nov 18, 2012 | Tunturi T85 Treadmill

    1 Answer

    Treadmill won't Deline....


    RUN the software calibration go under the HOOD motor and follow the instruction how to enter in the s. calibration for easy troubleshooting and fix it. see the schematic attached.
    God bless you
    11_13_2012_3_36_59_pm.jpg

    Nov 12, 2012 | Proform Exercise & Fitness

    1 Answer

    None of the touch buttons work. Fans, volume, speed, incline etc etc. The only two buttons that work are incline buttons 6 & 7. Power comes on and key turns on and off though. Can anyone advise??


    sorry but i dont have a solution for you!! i bought the t9ci back in nov of 2008, like you none of the buttons worked had to wait till march of 09 for nordictrack to send me a reprogram card, which did not fix the problem. i then recieved a new console, in april 09, which stopped working in feb 10. a service tech came out and had no clue, so the sent another new console which did not work. in march 10 they sent a whole brand new treadmill, and when i got on it last week the console was not working once again!!!!!!!!!!!!! i hope you dont have as many problems as i did

    Nov 05, 2011 | Nordic Track NordicTrack T9 ci Treadmill

    2 Answers

    We have an Epic 550 treadmill and the TV is upside down. When we first got it the TV was fine but we must have down something to get it upside down and no clue what we did! HELP!


    Just got off the phone with Icon. Here's the Fix: 1) With the remote control that came with the Treadmill press "Menu". 2) Then enter "1591" quickly with the number buttons. 3) Use CH or CH - to choose flip orientation. 4) Press VOL or VOL - to select 5) Press Exit
    That should do the trick!

    Aug 11, 2010 | Epic View 550 Treadmill

    1 Answer

    I am looking for a owner's manual for CardioZone treadmill Model CZ SG65. I can't find anything on the internet.....can anyone help?


    Go to treadmilldoctor.com or call them@ 1-800-750-4766 since Keys Fitness went out of business they bought the parts inventory I am assuming that they will have manual for you unit.

    May 07, 2010 | Cardiozone Supersport Hr Club Commercial...

    1 Answer

    My proform treadmill goes 10 mph no matter what speed it's set at


    That treadmill has to be calibrated upon replacement of controller. Contact the place were you bougth controller and request calibration procedure. Hope this helps.

    Apr 28, 2010 | Proform CrossTrainer Treadmill

    Not finding what you are looking for?
    Exercise & Fitness Logo

    Related Topics:

    96 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Exercise & Fitness Experts

    Electro Med Services...
    Electro Med Services...

    Level 3 Expert

    6694 Answers

    Howard
    Howard

    Level 2 Expert

    115 Answers

    Tom Chichester

    Level 3 Expert

    34711 Answers

    Are you an Exercise and Fitnes Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...