Question about Dewalt Saws

Open Question

Wiring a switch on a dewalt 1251 radial arm saw

Which wires go where

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rowdy45176
  • 2176 Answers

SOURCE: does anyone have a manual for a dewalt 710 radial arm saw

Go to Dewaltservicenet.com and in the middle of the page towards the bottom type in either 7710 or 710 it will take you to another page and find the model 7710 on the left hand side and then click on the user manual section to the right of it. The manual is 24 pages long. Hope this works if not let me know and I will look further. Thank you in advance for rating the information.

Posted on Apr 05, 2009

deme-tri
  • 90 Answers

SOURCE: Changing voltage on motor...

pull up the i.s. wiring code from that time
i.s. international standards.
the code change a few years ago

Posted on Aug 03, 2009

al_kupchella
  • 843 Answers

SOURCE: need replacement parts - accessories

If the kickback arm you seek is the type that is a round bar with pointed fingers on the bottom, I had the same problem. (different model DeWalt) I gave up trying to find one, and finally just made one. It was pretty easy, and works very weill I bought a piece of steel rod (1/2 inch I think) a steel repair plate (from which I cut a pair of tear-drop shapes with a hacksaw and file) a 1/4 inch hex-head bolt (which had about 1 inch not threaded) and a 1/8 inch roll pin. I looked at various pictures on the web to determine the shape of the teardrops. I drilled a 1/4 hole in the 1/2 rod. I cut the threads off of the 1/4 bolt so it was still long enough to accept the 1/2 rod, the two teardrops, 2 washers and the 1/8 roll pin. Then I put an 1/8 hole in the bolt allowing enough clearance so that the teardrops would swing freely. It works like a champ. One minor flaw is that with only two of the teardrops (instead of several) and being separated by 1/2 inch, it would be possible to make a skinny enough rip that only one teardrop would contact the board being ripped, leaving the other peice unguarded.

Posted on Jan 27, 2010

xxchemlight
  • 144 Answers

SOURCE: dewalt Radial arm saw switch

try to find someone on craigs list or ebay selling one for spare parts.

Posted on Mar 23, 2010

  • 7 Answers

SOURCE: craftsman radial arm saw 113-197751 wiring diagram needed

A friend just inherited a model 113.197110 and we are in the process of trying to restore it. I can draw you the wiring connections if you haven't figured it out yet.

Posted on Apr 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a manual for old DeWalt radial arm saw. Serial:60022464. NO model # on the plate.


check this out
http://www.fixya.com/support/t26033757-dewalt_radial_arm_saw_gw1_single_phase

20 Most Recent Dewalt 10" Radial Arm Saw 2 Hp Questions ...

www.fixya.com/support/p3534275-dewalt_10_radial_arm_saw_2_hp_403044_ma
Recent Dewalt 10" Radial Arm Saw 2 Hp 403044-made In Usa - Miter Capacity: 45° R 9.25" questions, problems & answers. Free expert DIY ... Serial:60022464.

Dec 11, 2016 | Dewalt Saws

1 Answer

My Dewalt 1251 radial saw just runs for a few seconds at low speed then cuts out. any ideas? - have changed the switch


Not for shure but it could be that this is the coil where the capacitor must be on connect to start up the motor.

Jul 26, 2016 | Dewalt Saws

1 Answer

Dewalt radial arm saw GW1- Is it single phase or 3 phase


if the plug on the cord fits any other outlet in the house it will be single phase
if the cord is cut , then it will have only 3 wires if it is single phase
( active , neutral and ground )
if it has 4 or more wires it will be 3 phase
most saws running a 200 mm blade or around that size and used for home duty will be single phase
the phase notation will be on the plate attached to the motor of the saw
It will read voltage , amperage, watts or hp, phase and cycles

Jan 02, 2016 | Dewalt Saws

1 Answer

Where can I find an owners manual for a Dewalt Radial Arm Saw Mdl # 02661


I would recommend clicking below. When you see a picture of your saw, open the link and contact the person who posted the picture on the internet.
Dewalt Radial Arm Saw

Oct 16, 2014 | Saws

1 Answer

Where can I find manual for dewalt 320 radial arm saw


You can use "dewalt 320 radial arm saw" to search in google

Jun 23, 2014 | Drills

1 Answer

I'm after dewalt radial arm saw dw320 manual where


Best place to get it would be to contact dewalt and ask them for a PDF file or photocopy of the manual sent via email. There are not very many places online that carry that manual.

Oct 07, 2013 | Radio Communications

1 Answer

Dewalt Radial arm saw switch


try to find someone on craigs list or ebay selling one for spare parts.

Mar 23, 2010 | Saws

1 Answer

Cannot find specs for my DeWalt Radial Arm saw


Here you go.hope this is what you wanted and Please rate this a fixya
714032d.jpg

Feb 09, 2009 | Dewalt DW746X 10" woodworker's table saw...

Not finding what you are looking for?
Saws Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dewalt Saws Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Parson's Repair...
Parson's Repair...

Level 2 Expert

206 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

Are you a Dewalt Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...