Question about Washing Machines

2 Answers

Fisher & Paykel GWL11 Top-Load Washer troubleshooting

Not pumping out rinse water. not spinning. just hums then goes to a warning beep

Posted by on

  • Anonymous Mar 14, 2014

    i have fisher and paykel washer the pump burnedup i want to know if the moduale is likely to be bad too i checked it and it seeums to be o.k.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I've had my washer for about 8 years. I experienced the same problem - pump stopped draining the machine. I called F&P and "Patrick" told me that I need to 1) unplug the machine, 2) tilt up the front of the machine, 3) spin the pump (plastic blades) until they turn freely (usually counter clockwise) but I turn it both ways till it turns freely, 4) plug the machine back in and press the buttons to get it back where it was - this has worked every time to get the machine going again. I do a lot of "dog laundry" and I'm sure the rugs/dog hair cause the problem. Hope this helps!

Posted on Nov 16, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 46 Answers

Hi the most common problem with f&p is the pumps,if it doesn't pump out it won't spin,make sure the bowl is not out of balance also that upset things is pump running if not pump may have failed or have something stuck in it
cheers grant

Posted on Oct 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced water pump and control panel, have power, but just beeps.


Fisher and Paykel GWL11 Top Loading Washer

ths.gardenweb.com > Home Forums > Laundry Room
Mar 5, 2008 - My GWL11 Top loading washer has had nothing but problems! ... 4) (Rinse Phase) Drain the water, then lock the lid for spin. ..... I plug the power cord in and I have nothing on the control panel. ..... As the controller was only replaced early in January, I've flicked F&P NZ an email to see if it's still under ...

How to repair a Fisher Paykel Washing Machine

www.instructables.com/.../How-to-repair-a-Fisher-Paykel-W...

InstructablesI removed the pump and control panel, found no blockage in the pump, so far ... Ihave just tried to fill my F/P machine but the water is just dripping in. ... I have aFisher Paykel washer have replaced the control module and now it .... washing machine MW612, stopped working and displayed beeping sound every second.

Jan 16, 2016 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Hello my Fisher Paykel washer will go through the


clean the pump at the bottom of the washer (its the piece with the fan attached); also check the hoses at the pump

Jun 27, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher paykel washer won't go into rinse cycle. Stops and gives steady beeping tone


http://www.docstoc.com/docs/25379677/Fisher-and-Paykel-Circuit-Diagram-GWL11
www.fisherpaykelparts.net/partmanuals/GWL11US.pdf - United States Above is a circuit, and a service manual, below are two DIY Washer help sites, to help troubleshoot and repair, the service manual has all troubleshooting and repair instructions.
http://www.washerhelp.co.uk/diy-repair-help.html
http://www.repairclinic.com/Washing-Machine-Repair-Help

Jun 01, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

My Fisher and Paykel GWL11 washer will not finish a cycle. It goes to the rinse and spin part and just sounds an alarm and will not do anything else or advance any further. What would the issue be?


It would be putting up a sequence of lights across the top.that is a fault code..I don't know if it's stopping when it's trying to drain the water or if it is in fact draining the water,all i can say is if its not draining even the first load of water then it's likely to be a blocked or jambed pump.code 37 should mean pump problem.When the machine is beeping,the lights on the top row must be read from right to left in binary code.eg 128,64,32,16,8,4,2,1 these are the binary numbers for each light across the top row.Add together only the ones that are on.that will be your fault code.

May 22, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Water is not draining and rinse light is flashing


top load fish pak washer wont dump or spin.constant beeps. rinse spin light and center wash light on .could dump valve be bad or how could line get clogged for dump

Nov 03, 2009 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Stops before rinse cycle... won't drain or spin.


The REGULAR CYCLE button turns the drain pump on or off. The REGULAR LED will turn
on when the pump is on. This feature can be used to drain the tub. You could get a bucket and lay the hose on the fllor. Gravity will drain it down.

Sep 07, 2009 | Fisher and Paykel GWL11 Top Load Washer

2 Answers

GWL11 fails to drain


I had the same problem. After bailing out the water, I tipped the machine and saw a knee high panty hose caught up in the fan on the bottom. I removed that, checked to make sure the fan could spin freely, and viola! problem solved!

Jun 20, 2009 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher and Paykel GWL11 Question


no belts ..direct drive ..lean washer back pump is a twist lock no tools needed hose clamp can be removed with fingersremove pump and ck for lock impeller also ck the diverter valve just behind pump

Jul 16, 2008 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher & Paykel washer - manufacturer in October 2005


Please follow link Might require free sign up.
According to my experience it sounds the your pump is blocked or outlet of water obstructed.
Normally when pump cant be activated you get this problem.

May 18, 2008 | Fisher and Paykel GWL11 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

63291 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...