Question about Kenmore 22422 Top Load Washer

1 Answer

Model 110 washer will not go into a final high speed spin.

What would cause my washer not to do a final high speed spin? Leaves the clothes quite wet. It does spin fast during rince cycles and g the final spin cycle but will not go into the very fast spin required to sipn out excess water.

Posted by on

  • 3 more comments 
  • Anonymous Nov 13, 2008

    Everyhting seems good until the end of the cycle...clothes on the bottom are soak wet

  • Anonymous Nov 24, 2008

    I have the same problem. Do any of you know what could cause this problem?

  • ashraf6900 Feb 15, 2009

    Kenmore 110 24622300



    It works fine in all modes except the high spin cycle where it will not reach the high speed spin. The close comes out soaking wet when the tub is loaded with with medium to large loads?

  • Anonymous Feb 17, 2009

    top load

  • Anonymous Mar 16, 2014

    Does not spin fast

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 63 Answers

Is it top load or front loader kenmore what

Posted on Nov 12, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Whirlpool duet fw95hedco washer won't spin at max speed & leaves all clothes wet. No error codes during tech diagnostic visit. Washer only 18 months old.


Possible Defective washer transmission. Do you overload the washer with heavy items like towels or blue jeans very often? That can cause early failure.

Feb 16, 2017 | Whirlpool Washing Machines

1 Answer

Wont final spin


sorry have not come across that model its not within my expertise

Nov 14, 2011 | Washing Machines

1 Answer

Why does the washer stop during a load and "F 06"


Hello,

The F6 error code means that the computer on the control didnt detect that the motor reached a high speed on the spin cycle, sometimes it thinks the washer didnt spin fast enough because of a loose wire connection either on the motor or the control boards (motor &machine control) if you find that the washer did actually spin at high speed (clothes dont come out sopping wet at the end of cycle) the wire connections or the motor control board will be the potential causes of the F6 error code



GENE

Sep 09, 2011 | Kenmore HE2 Plus Front Load Washer

2 Answers

I have a magic chef 20 lb capacity heavy duty washer model W20HN3S serial ME851474 with spin problems. Clothes come out soaking wet. Can I replace a belt?


If your washer will wash (agitate) your clothes but does not spin well, you will need to replace the "thrust bearing" in the washer. The repair is simple and will only take you a short to do. Here is a link to the "thrust bearing kit" you will need.

Jan 07, 2011 | Chef Cooking Magic Chef Washing Machine...

1 Answer

I own a Kenmore washer Model 110.22722100. The last couple of weeks, it leaves the clothes wet. It drains like it is supposed to and spins. What is causing this to happen?


If the washer doesn't reach its proper spin speed, the clothes may be too wet at the end of a cycle. Check to be sure the load is properly balanced and run a spin cycle again. If the clothes are still wet, you may have a worn or loose belt (Maytag®), a worn clutch (GE®/Hotpoint®), or a worn motor pulley or tub bearing. Replace the applicable component.
Here is the part you will need.

Nov 28, 2010 | Kenmore Washing Machines

1 Answer

Clothes seem too damp after final rince


its a washer ,not a dryer....if the spin setting is set low the clothes will feel quite wet....reset to a faster spin cycle if needed.

Jul 26, 2010 | Whirlpool LSQ9549P Top Load Washer

1 Answer

We have a Whirlpool LSN1000PQ3. What would cause my washer not to do a final high speed spin? Sometimes it makes the sound like its spinning, but its just sitting there. I can manually (stick my hand in it...


it seems that the automatic spin clutch is slipping so the only thing you can do is consult the whirlpool engineer as its a one off machine for specialised spares only the very experienced people can repair eric

Dec 23, 2017 | Whirlpool Washing Machines

1 Answer

Frigidaire Tumble Action washer won't complete the final spin. leaves clothes soaking wet.


Had the same problem and fixed with ease. The problem is with the door lock. There is a secondary locking mechanism that kicks in for the final spin due to the high speed. When the secondary lock goes bad the washer will not do the final spin. The replacement part is under $40 @ AppliancePartsPros.com .

Dec 08, 2009 | Frigidaire 14 Cycle Tumble Action Washer

Not finding what you are looking for?
Kenmore 22422 Top Load Washer Logo

1,774 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal De

Level 3 Expert

2670 Answers

fordexpert

Level 3 Expert

5626 Answers

Robert Rankin

Level 2 Expert

356 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...