Question about Nview Z215 10.4" LCD Panel with Video(16.7 Million) Z215 Multimedia Projector

Open Question

NView Z110 panel for OHP

I have an nview z110 panel for use with ohp. when i connect to my laptop running XP the panel says no video. when i connect to my old tower running 98 it project output during booting up but then reverts back to no video at a cetain point in boot process. help with either source would be appreciated

Posted by on

2 Suggested Answers

  • 3 Answers

SOURCE: dlp nview projector help

the unit is reading hot then turns light off. blow out any dirt you can see, and re try. If that does not help then you have an internal component problem.

Posted on Jan 13, 2008

projdoc
  • 2236 Answers

SOURCE: Projector will come on but lamp will go out

still too warm. it need to cool down more. could also be a ballast issue. if the caps are drying out, a boost of power could overload it and it'll shut down.

Posted on Aug 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

NEC VT470 Multimedia projector


Try to reset the projector. Turn the power off. remove the power supply cable from the main socket. Leave it for 30 min. Turn on again. Before turn on(Make sure) 1.0 power cable install correctly 2.0 Lamp cover install correctly. 3.0 No excessive heat around the projector All this can be refer to the user manual.

Sep 23, 2007 | Nview Z215 10.4" LCD Panel with Video(16.7...

1 Answer

I think a thunder storm messed up my projector. The green light on the power button does not light up.


sounds like a voltage surge has taken it out. could be a simple fix with a fuse replacement, or a more complex destruction of the mains input circuitry and overvoltage protection devices fused and copper tracks blown.
I quick examination by a technician cam suss it out for you

May 21, 2011 | Nview Z215 10.4" LCD Panel with Video(16.7...

1 Answer

My infocus X3 projector won't come on, I get a green light at first and then it turns red. What is the problem?


Hello,
Well the single re blink of the LED indicates Lamp failure. Though most likely there can be a few other causes for your lamp not lighting. here's the most likely problem if the lamp has not failed.
It could be the lamp power supply (ballast) has failed.
Or if you don't hear the fans running either there is a possibility the "over-temp" sensor has failed.
If the fans are running I would try replacing the lamp.

Take Care!

Oct 16, 2009 | Nview Z215 10.4" LCD Panel with Video(16.7...

1 Answer

Projector will come on but lamp will go out


still too warm. it need to cool down more. could also be a ballast issue. if the caps are drying out, a boost of power could overload it and it'll shut down.

Aug 06, 2009 | Nview Z215 10.4" LCD Panel with Video(16.7...

1 Answer

No signal optoma ep739


Hi,

One good thing is that you are running XP. Will work on the premise (that you have posted) worked before and the driver (ForceWare91.31) was the only thing changed.

Let's try the easy ones first. Activate twin/dual view in your Display Properties. Right click on any clear area of your desktop, click on Properties, click on Settings tab, select monitor 1 or 2 depending which is your primary and which is your projector. Check (or uncheck-whichever works) on box "Extend....". Apply, OK.

or

do the same with nView Properties.

The hard ones are registry and/or inf editing, though I am reluctant to even suggest.

Incidentally, there is an application that is supposed to facilitate twin or dual view configuration, UltraMon. This may be better/safer way to address your concern.

If all else fails, you may have to rollback/downgrade your driver.

Cheers.

Jan 20, 2008 | Multimedia Projectors

1 Answer

Projector won't turn on after I replaced the lamp


re insert the lamp and check your connection. if that does not work then replace lamp or have lamp checked.

Dec 03, 2007 | Nview Z215 10.4" LCD Panel with Video(16.7...

1 Answer

Dlp nview projector help


the unit is reading hot then turns light off. blow out any dirt you can see, and re try. If that does not help then you have an internal component problem.

Sep 26, 2007 | Nview Z215 10.4" LCD Panel with Video(16.7...

1 Answer

Proxima x350


Did you have an image before? if not, sounds like you did not switch your laptop to the lcd screen (fn f5) keys. Please advice

Jun 08, 2007 | Nview Z215 10.4" LCD Panel with Video(16.7...

Not finding what you are looking for?
Nview Z215 10.4" LCD Panel with Video(16.7 Million) Z215 Multimedia Projector Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nview Multimedia Projectors Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

The Knight
The Knight

Level 3 Expert

68258 Answers

Are you a Nview Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...