Question about Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Machine freezing with three lights flashing.

Machine is freezing with three lights flashing (power light, reduce creases and mini load lights all flashing. Have tried reseting machine by plugging out and turning it off. Have also tried restarting wash which result the the same problem reoccurring again.

Posted by on

  • dayvidc Oct 24, 2008

    i have a wma46 with the same problem.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

HI JOHNNYHEFF,
JUST GOT A NEW HOTPOINT STARTED TEST WASH ALL THE LIGHTS FLASHED SO SWITCHED OFF TRIED AGAIN NO JOY. TECHNICIAN COME OUT SAID THE CIRCUIT BOARD WAS GONE, NOT GOOD NEWS FOR YOU BUT THOUGHT I'D LET YOU KNOW!

Posted on Nov 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hotpoint washing machine WF560 mini load and reduced creases lights are flashing and also the on/off light is also flashing, please help. Thanks


Heating eliment or PCB, is this when doing a prewash? or a normal wash excluding pre wash?
if you can manualy pump out and manualy rinse and spin, my guess is heating eliment is broke £20-£30

Jan 27, 2011 | Washing Machines

1 Answer

Hotpoint WF541 problem


Technical Fault is Pressure switch jammed on empty: check switch & module... in laymans terms its either a blocked sump hose or faulty pressure switch/module

Mar 13, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

The mini load and reduced creases light flash when washing has finished, but its as though it hasn't been spun properly


I should check the filter if I were you.
Remove lower rear panel of washer, remove large black hose on bottom of drum, remove and clean filter inside hose.
Please rate my solution.
Thanks.

Nov 03, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

Hotpoint wf540 stopping on a rinse and spin and


check pump/filter/outlet hose for blockages. if ok, check pressure switch (disc shaped item at top of machine with 4? wires and a tube) by blowing into it gently - should hear clicks, then blow into tube to pressure chamber - should be clear.

Oct 26, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Lights flashing on WF320P


i'm having same problem people have said empty filtter but i have done that and the water is running out but still flashing
so sorry wish i could help.

Sep 05, 2009 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hi my hotpoint wf541 will not run the start stop light and the mini load light are flashing i believe these are fault codes but have no refrences to what they are


I have encountered a similar problem. The following lights were flashing on and off:

  • On/Off.
  • Reduced creases.
  • Mini Load.
I also found that previously one of the 'lifters' inside the drum had broken off and someone had tried to put it back in place and continued to use the washing machine. After a short period of time the above mentioned flashing lights began.

I first suspected the pump, but this was fine. I then disconnected the hose which connects the hole from the drum to the pump and I found a child's sock blocking the hose. I removed the obstruction, put it back together and the machine worked perfectly. I also replaced the lifter (apparently these break quite often) and the machine has been working perfectly ever since that day.

I hope this helps. Good luck.

Apr 04, 2009 | Washing Machines

3 Answers

Reduce crease and mini load lights flashing on hotpoint wf541g. had pump failier and have replace with new on but still not pumping water out.


I have encountered a similar problem. The following lights were flashing on and off:

  • On/Off.
  • Reduced creases.
  • Mini Load.
I also found that previously one of the 'lifters' inside the drum had broken off and someone had tried to put it back in place and continued to use the washing machine. After a short period of time the above mentioned flashing lights began.

I first suspected the pump, but this was fine. I then disconnected the hose which connects the hole from the drum to the pump and I found a child's sock blocking the hose. I removed the obstruction, put it back together and the machine worked perfectly. I also replaced the lifter (apparently these break quite often) and the machine has been working perfectly ever since that day.

I hope this helps. Good luck.

Mar 10, 2009 | Hotpoint Aquarius WF000 Front Load Washer

4 Answers

HOTPOINT AQUARIUS WF 250 ON/OFF LIGHTS FLASHING


The lights are set off by the balance sensors.And if your balance sensors are  stopping    it from spinning than you first have to make sure the washer is level.You  could have bad Shocks and a bad electronic control board,.                                    

May 05, 2008 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WMA42 Front Load Washer Logo

681 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...