Question about Car Audio & Video

Open Question

Burned SMT in Acura NSX Bose

Hello, I am currently repairing a Bose car stereo from an Acura NSX. On the bottom name plate of this car stereo it reads ACURA Accessory P/N:39100-SL0-A000-M1, Ref No.: CM3939. I have found that one SMT part (Q704) has been burned beyond recognition. I already finished replacing the leaking capacitors on the main board. I need help in identifying this burned Q704 located underneath the vertical board that holds the main electrical connector.

Posted by on

5 Suggested Answers

DrElectrics
  • 199 Answers

SOURCE: honda car code

You can ring honda. With the information you provided they can give you the code to the radio without a problem.

Posted on Mar 16, 2008

  • 1 Answer

SOURCE: code of my acura 39100-st7-a500

I have the same problem. Have you found the code/solution?

ixadeth@hotmail.com

Posted on Jul 30, 2008

dr_greg
  • 192 Answers

SOURCE: Need code for Acura radio?

this should be your code # 24263.. make sure to clear the memory if u have tried entering any other numbers by removeing the battery terminals for a min or so...

Posted on Apr 08, 2009

  • 43 Answers

SOURCE: acura integra radio unlock code

call or stop by your local honda dealer. they should be able to help you. there shouldnt be a charge.

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: have 1997 Acura CL.. need radio code. Acura

Remove the ash tray and the code is on the back of the ash tray.

Posted on Oct 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A problem started with my Panasonic CQ-C9700N car stereo recently which involved the complete facia powering off. However the stereo would still work in the mode it was left in. Every now and then it would...


if im not mistaken, that model has a detachable face plate. What happens a lot of the time is the connections between the face plate and the unit get corroded. Take the face plate off and (with fine grit sand paper) lightly scuff the electrical connection clean on both the unit and the face plate. It also doesn't hurt to use a little dielectric grease before you reattach it... this method has work several times in the past for me... Hope this helped!

Apr 29, 2010 | Car Audio & Video

1 Answer

My Bose car stereo has been removed from car ,would like a wiring diagram,or info to go somewhere online to get free help


What is the brand name? In general, the following can be:

Black: Ground
Red: Switched +12V
Yellow: Constant +12V
Blue/W stripe: Remote control
Last 8 wires for 4 speakers.

I hope this helps.

Suleiman

Mar 20, 2010 | Car Audio & Video

3 Answers

LCD panel on a Bose stereo in a 2002 Mazda Miata LS doesn't work!


i have the same problem... and it hasn't anything to do with the orange backligh.. it's the lcd segments themselves that have slowly started disappearing.... pressing hard on the middle of the top edge or the top left corner usually brings the numbers back for a while...

i think this is a loose connection / contact corrosion issue that seems to be common to 2002 miatas (i've seen at least 3 that have the same issue with nearly the same milage ~20k-40k)

Jun 13, 2009 | Car Audio & Video

1 Answer

Problems with kenwood kdc-mp2028


The remote from the amp should be connected to the remote (blue wire) or power antena wire from the radio.

May 15, 2009 | Kenwood KDC-MP235 CD Player

1 Answer

Bose delco cd radio for 97 pontiac


I don't know your experise when it comes to repair. This problem is normally a bad laser or spindle motor. You can clean the laser and spray a Cleaner/Lubricant into the openings on the bottom of the spindle motor. This is a common problem I see with this stereo when it comes to repair.

Nov 15, 2008 | Car Audio & Video

2 Answers

Displays ER-3:


According to the manual er-3 is a "Servo error or the disc is in upside down". I wish i were kidding but that is what the manual says.

Sep 01, 2008 | Durabrand DB1200 CD Player

1 Answer

Stuck cassette in bose care stereo


I wonder if you were ever able to resolve your problem... I have a2000 ML 320 witht he same Bose issue... I get an error msg: TAPE TOO TIGHT... It won't even play and I get that same clicking sound when I try to eject... When I first purchased vehicle (used in 2002) I had the problem and the dealership assured me that they replaced the stereo with a new one...I never really tired it again until more than a year later and the same thing happened... Of course I was out of warranty at that time and I can't help, but to wonder if they really ever changed the stereo, or if they just removed the cassette.... If any has the solution, please contact me via email: msshazz@gmail.com

Mar 16, 2008 | Car Audio & Video

1 Answer

Jensen CD3720 car stereo unit face plate LCD display blanks out.


The substrait is probably cracked, that's the circuits inside the pc board of the faceplate. It will cost you too much to try to have it repaired. If you will wait for a few days I may have a face for it as I'm currently trying to fix one that is blowing fuses. I'm not going to spend a whole lot of time on it. I'll let you know.

Feb 28, 2008 | Jensen CD3720 CD Player

1 Answer

About scheme


Try another repair shop. We repair stereos everyday without schematics.

Sep 08, 2007 | Alpine MDA-7755

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4737 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

66126 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...