Question about HP LaserJet 3330 All-In-One Printer

1 Answer

10.21.08 question Did you get a response to your posting on 10.21.08? I have the same question. I can't see the sensor, therefore I don't know where it's located; where to check.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 66 Answers

Hi,

the sensor of that printer is in the back, try to open the back plate cover you can see it there..

Posted on Oct 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I posted about an outdoor light and got a response about a vehicle I don't own.


Sorry about that!
Could you describe your problem again?
Be Blessed

Jan 27, 2013 | Cars & Trucks

1 Answer

My name is Patricia Taynor my 1996 grand cherokee is not getting any spark to start we replaced the coil but what else can i do ?


I think it is the CPS "crank shaft position sensor" If this sensor goes out, it don't know what position the crank is in so therefore it will not fire. This is a BIG problem with the cherokee. The part is about $60 and usually located where the transmission meets the back of the engine. Very easy to replace. Since I'm not there it's not 100% sure but I would not be scared to say 95% since it is an issue. Good Luck...

Jan 06, 2012 | 1996 Jeep Grand Cherokee

1 Answer

97 Olds Cutlass Supreme SL. Transmission 4T60E (M13). Which solenoid is the 1-2 shift solenoid? I am a Guru on FixYa. Done all except internal transmission stuff. Help me out here. Its my car. I posted...


I had that same problem on an Aurora. I don't remember which one, but I do know that I called a gm dealer and had them fax me the diagram location. The internet's diagrams were all too general.

Aug 31, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Hi I have a 2004 volvo s60 and recently had to replace the o2 sensor because it kept stalling ...2 months later its doing the same thing. It stalls every now and then mostly when im slowing down to stop....


A throttle position sensor will also do that because the engine doesn't know what it is receiving and what to to do.If you have any questions or need more help,just comment here and I will get an autolink to your post and reply ASAP.I really encourage responses so I can follow up properly as I know where you stand and asking someone else restarts all the explaining because we cannot see other 'Expert's' responses.Good luck,Greg

Jan 05, 2011 | 2004 Volvo S60

1 Answer

Truck is jumping and the code is P0340 crankshaft sensor what caused this?


Sounds like the sensor is getting to completely fail. It works off the rotation of your crankshaft. If the sensor is going bad or goes out, the sensor don't detect what position the crank is in and therefore it will start cutting out and shortly cut off because the sensor don;t detect the reference point on the crank.

Mar 01, 2010 | 1997 Nissan Pickup

1 Answer

Hey Taran..thanks for ur reply. i don;t have that driver on my computer and therefore i also did have a look at that link. could u please assist me in telling me what driver i should download as i have...


HI,

Can you specify your problem more briefly,Please?

May i know, for which product you were searching for drivers and may i know, whether you get any Yellow Exclamation mark for any particular product in the Device manager?

Please post your question as a comment, and we may solve your issue.

Thanks
RNJ VINODKUMAR

Oct 02, 2009 | Office Equipment & Supplies

1 Answer

1993 Ford Escort 4 Door Byockey830


speed sensor is only used to tell the processor to shift the trans into overdrive and lock up torque converter, don' know what the orig post was, try to always use the same thread to post new questions about the same issue.

Mar 08, 2009 | 1993 Ford Escort 4 Door

Not finding what you are looking for?
HP LaserJet 3330 All-In-One Printer Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Seeker5211
Seeker5211

Level 3 Expert

1089 Answers

kakima

Level 3 Expert

101466 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...