Question about Kenmore Dryers

1 Answer

Kenmore 110.86870100 Has power to the power block but the start button will not start the dryer

Door switch and start switch are functioning properly. Thermal fuse has continuity mea., 0 ohms,Operating thermostat Ohms, Thermister 3.5 RX1K, Thermal cut-off & High limit thermostat 0 ohms. Heater element 10 Ohms and not shorted out. Timer doesnot indicate it is operating. Machine appear totally dead.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kenmore Master
  • 1,344 Answers

Get the schematic and look at the timer. there are two wires that you can jump across and verify that the timer is bad by bypassing it all together. If all your checks tested good then the timer is bad. If you have any doubt order the part from repairclinic.com because you get a full refund even if you put it in and it does not work

Posted on Jun 05, 2012

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

TheMobilian
  • 8220 Answers

SOURCE: Kenmore 84152 /94152

probably the heater

Posted on Jan 15, 2009

TheMobilian
  • 8220 Answers

SOURCE: Kenmore Dryer Model 110

If all of the components are reading ok then you need a timer. Touch your 2 leads together. 0 ohms rght. That means you have a complete circuit.If you get the 0 reading then the element must be otay. Bad timer. Take that fancy meater of yours and atttach one of them leads to the timer leg marked RH. Yank the wire off the terminal beore you test. Move the timer around. You should get the famous 0 reading along the way. If you don't then that means you have the bad timer.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Kenmore 90 series dryer, motor wont start, loud


Hi,
  • Check to see whether there's power getting to the dryer. Is it plugged in? If you plug something else into the outlet, does it work? If not, check for a blown fuse or tripped circuit breaker.

  • If the door switch or the door-switch actuator is defective, the dryer won't work and you need to replace the failed component. The switch is inside the dryer main housing near the door frame. Sometimes you need to raise or open the top or front of the dryer to reach the switch.

  • Often the main wiring connection from the house, at the dryer, burns and the connection breaks. In this has happened to your dryer, you need to replace the power cord and the terminal block inside the dryer to which the wire is attached.
Hope this will fix your problem for sure.

May 10, 2010 | Kenmore Dryers

1 Answer

Our Kenmore Elite HE4 gas dryer will not start although all controls on front are lite and appear to be functioning properly (settings can be changed, etc). I has been working fine for several hours until...


check the door switch and door latch. Open door, set the dryer to air fluff cycle, and manually depress the door switch. Press start button. If it started - door needs alignment to fix it.
If it did not start:
If your dryer has light inside - check if light turns off when you press the switch. If not - switch needs replacement.
If all that checks out ok - the problem is more serious, and you might need a tech to come out and diagnose it.

Mar 04, 2010 | Kenmore Elite HE4 Electric Dryer

1 Answer

Kenmore dryer not working


replace the thermal fuse this part is on the blower housing unit. you will see it when you take the back panel off. its about 2" long with 2 wires. white black strip on inside.

Nov 06, 2009 | Dryers

1 Answer

THE DRYER DOESN'T START BUT IT HAS POWER GOING TO IT


Verify dryer door switch is not defective...Button/pin depresses and is not loose. Verify that door switch has continuity when pushed in. Verify start button is working. Verify that rotary timer has poower going to it and timer is working properly. Check for any blown fuses inside dryer...might be located on a control board. Thermal protection sensor may have tripped and did not self-reset so check that.

Sep 26, 2009 | Kenmore Dryers

1 Answer

Won't start - 3 beeps when Start button pushed


CHECK THE FOLLOWING--

1. No power to the dryer
Make sure there's power getting to the dryer. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power with a voltmeter or by plugging something else in. Sometimes the power cord disconnects or burns at the dryer, if this is the case, the wiring and the terminal block must be repaired or replaced.

2. Door switch / Door switch actuator lever
The dryer would not start with a broken door switch. Replace the door switch if found defective.

Most dryers have a door switch actuator lever - when you close a dryer door, it presses against the lever, which actuates the door switch. If the lever is broken, the switch would not activate and the dryer would not start. Replace the lever, if broken.

Note: Door switch actuator lever usually comes with the door switch assembly and it is recommended to get the whole assembly since there is almost no price difference between the door switch assembly and just the lever.

May 31, 2009 | Kenmore Dryers

1 Answer

Kenmore dryer does not turon on


CHECK THE FOLLOWING---


1. No power to the dryer
Make sure there's power getting to the dryer. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power with a voltmeter or by plugging something else in.

2. Door switch / Door switch actuator lever
The dryer would not start with a broken door switch. Replace the door switch if found defective.

Most dryers have a door switch actuator lever - when you close a dryer door, it presses against the lever, which actuates the door switch. If the lever is broken, the switch would not activate and the dryer would not start. Replace the lever, if broken.

Note: Door switch actuator lever usually comes with the door switch assembly and it is recommended to get the whole assembly since there is almost no price difference between the door switch assembly and just the lever. Check your model for more details.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Note: It is recommended by most dryer manufacturers to replace a hi-limit thermostat when replacing a thermal fuse.

4. Timer/control
Replace if defective (note: uncommon problem).

May 31, 2009 | Kenmore Dryers

1 Answer

Dryer will not start have replaced the heating element, door switch and on switch


hi, i recommend inspecting the terminal block that the power cord is connect to on the back side of the dryer. this terminal block may be faulty or, the cord could be lose and not connected properly.kindly, inspect this device that is located on the back side of the dryer for lose connections. if the termainakl block is in good conditon and, the power cord is screwed on tight, thsi iwll confirm timer fialuer.

replace the timer in this case.

May 20, 2009 | Kenmore Dryers

1 Answer

HE5 Dryer not working


Hello dram65,
Check the door interlock switch, if that's malfunctioning or not sensing the door is closed.. it will disable the drying function,
Regards,
Rick

Dec 13, 2008 | Kenmore 82822 Electric Dryer

1 Answer

Dryer won't start due to delay button lights up and won't go off


1. No power to the dryerMake sure there's power getting to the dryer. Check for a tripped circuit breaker or a blown fuse. Check the wall socket for power with a voltmeter or by plugging something else in.

2. Door switch / Door switch actuator lever
The dryer would not start with a broken door switch. Replace the door switch if found defective.

Most dryers have a door switch actuator lever - when you close a dryer door, it presses against the lever, which actuates the door switch. If the lever is broken, the switch would not activate and the dryer would not start. Replace the lever, if broken.

Note: Door switch actuator lever usually comes with the door switch assembly and it is recommended to get the whole assembly since there is almost no price difference between the door switch assembly and just the lever. Check your model for more details.

3. Thermal fuse
Most dryers have a thermal fuse, which burns out when the dryer overheats, in which case the dryer will either not run at all or stop heating. The fuse is usually located on the vent duct, inside the dryer. A blown fuse will show no continuity when measured with a meter. Before replacing the fuse, make sure the blower wheel is not broken or clogged, and there is nothing blocking the venting.

Note: It is recommended by most dryer manufacturers to replace a hi-limit thermostat when replacing a thermal fuse.

4. Timer
Replace if defective (note: uncommon problem).

Nov 09, 2008 | Kenmore 659 Electric Dryer

2 Answers

Kenmore elite he3 electric dryer


If you get a series of four rapid beeps when you push START in an attempt to start your dryer, your door switch (interlock) is defective.  I have experienced this problem before and it is a fairly simple problem to fix.  The easiest way to tell is to open the dryer door and push the door interlock in by hand.  Hold it in while pushing the START button.  If the dryer starts, then all you have is a simple problem of the door not closing properly.  If the dryer still does not start, however, replace the dryer door interlock.  The interlock should also make a definite "click" while pushing it in.  If it does not, the switch is worn out.  Some dryers have an upper and lower door interlock.  If yours is equipped with two interlocks, make sure they are both functioning and that the door is latched properly.  I have experienced problems where dryers doors with two interlocks would close at the top, but not at the bottom.  The dryer would not start as a result.  If you can provide me with your model number I can get a part number and price for you.  I can also tell you where you can get the part and provide instructions on how to replace it.  Let me know.  I hope this helps you.

Oct 31, 2007 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Sal DeAngelo

Level 3 Expert

2122 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Kenmore Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...