Question about Whirlpool Kitchen Ranges

1 Answer

Digital screen blinking F5 and beeping - Whirlpool Kitchen Ranges

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a sears elite and when we turn oven on f5 code comes on..

Posted on Feb 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool oven question...FSEO on display after about 5 mins of oven operation..beeps continuously,oven shuts off...dinner ruined!


If you receive error codes F5-E0, F5-E1 or F5-E2, the door and latch switch need checking and possible replacement.

The door switch is #12 in the diagram (click image for zoom)...

zjlimited_449.gif

Hope this helps.

Jun 22, 2011 | Whirlpool RF364 Electric Kitchen Range

1 Answer

KitchenAid KEDT105V Electric Stove - f-5 beep Started beeping out of the blue, pushed cancel and it stops for 20 seconds then continuous beeping. If the oven is on the beeping will stop. Hope you can help,...


Hi, F5 means your control board may have suffered a fatal error. Unplug the unit for 30 seconds, when the power is re-applied if the error comes back you will need to replace the control board (ERC). Mike

F5 Board failure Replace control board (also called ERC or clock).

Mar 25, 2010 | KitchenAid KESC307 Electric Kitchen Range

2 Answers

My Whirlpool Accubake super capacity 465 self-cleaning oven does not work. When started E1 -F5- appears on screen. Model# RF 386 PXGO. Serial# RJ0525903.


The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.%#FDG

Jan 02, 2010 | Whirlpool Accubake RF362LXTT Electric...

1 Answer

Self cleaning is done and the macjine keeps beeping and E1 F5 is blinking. i dont have the manual and dont know what these error codes are or how to stop them. i tried turning the dial to the off position...


The E1- F5 error is a door lock error.

The control (TIMER) has likely failed in this instance - BUT...

Sometimes when you disconnect power to a range and reconnect it the electronic range control gets confused.
You should disconnect power again for 15 seconds and reconnect and see if that helps.

If it doesn't cure the E1- F5 error hold the bake button in until E0- F2 appears in the display.
This is the error for a stuck button on the keypad and is the way to clear the memory of the electronic range control.

Sometimes these work, but if the control has failed it won't make any difference.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.^&^$YRG

Oct 17, 2009 | Roper FEP320 Electric Kitchen Range

1 Answer

F5 error


HI. I have researched this fault code and this is what we came up with.


F5 Board failure Replace control board (also called ERC or clock).


Mar 21, 2009 | Whirlpool GR465LXLS Electric Kitchen Range

3 Answers

F5E1 error


Whirlpool-KitchenAid-Roper Appliances: Oven Fault Codes:
>>Exception Note:<<
Chart below does not apply to Whirlpool Models using the "Y" line in the products model numbers. Applies to models using 4 digit displays only.

F0-E0 Analog to Digital failure
Disconnect panel for 30 seconds
Should the above error re-appear, replacement of the control is required.
F1-E1 Defective ERC Replace ERC
F2-E0 Shorted Keypad Replace Keypad
F3-E0 Sensor or Sensor Fuse Open Replace Sensor or Fuse
F3-E1 Shorted wire or Sensor locate short and correct it or replace Sensor
F3-E2 Oven over heat Replace Sensor
F3-E3 Cleaning Temp over heat Replace Sensor
F5-E0 Door Error Check Door
F5-E1 Door Latch Check Latch
F5-E2 Door Switch Check Switch

May 11, 2008 | Whirlpool RF378 Electric Kitchen Range

2 Answers

Whirlpool Electric range model RF386


cant nfind euf5 code can find eo f5 its a door loc code saing the door and latch switches do not agree try pushing stop/cancel and try again also does the oven light go off and on when you open and close the door

Dec 31, 2007 | Whirlpool RF364 Electric Kitchen Range

2 Answers

Problem codes for self-cleaning ranges


My experience (Kenmore Ultra-bake Model 665-72002102) was that E1 F5 meant an error with the oven lock switch. In our case, the latch was partly stuck from food or other debris. Just moving the latch back and forth loosened the scale that was making it stick, and it worked again.

Dec 05, 2007 | Kitchen Ranges

2 Answers

Oven door will not unlock


morobie The error code "F5 E1" means "Door latch not operating". To help you better I need the complete model number for you range. You can find it on the frame behind the storage drawer. Gendos...post back

Jan 30, 2007 | Kenmore 91112 / 91114 / 91117 Electric...

Not finding what you are looking for?
Kitchen Ranges Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Cindy Wells

Level 3 Expert

4761 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you a Whirlpool Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...