Question about JVC RX-6030V Receiver

1 Answer

Where is the microcomputer located in the jvc rx6030v?

I see the code pop up just before the unit shuts down....dsp micom ng

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • JVC Master
  • 74,459 Answers

Hello
The microcomputer, otherwise called as system control can be located on its main board. Some sets will have it on its front panel baord, along with the display unit board.

Posted on Feb 08, 2012

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: JVC RX 6042

just google jvc go to customer service at the bottom look up manuals and u can print it right off the internet no cost

Posted on May 18, 2008

VOTIT
  • 2071 Answers

SOURCE: JVC A/V Receiver RX 7042S - DSP NG

it seems the problem of your unit is in the power amplifier section,the IC chip there is defected that why only analog source .you better bring back to them the unit it is the only option, that is there back job...

Posted on Jul 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

This jvc rx6030v receiver every time i try to hook it up to the speakers it comes up sayin overload, any suggestions


If you are hooking up multiple speakers and they are in parallel, that will happen. Try just one speaker. If it does same with just one speaker on a channel, then there is something seriously wrong with the amp(s).

Apr 01, 2017 | JVC Audio Players & Recorders

2 Answers

Display message "DSP NG"


Hi pay attention to do all interconnections right
You can get help dowlowding a low cost service manual at link below:
http://www.smpcshop.com/VSX-D414-VSX-D512-p-5216.html
Have a nice day and Good luck

Feb 21, 2008 | Pioneer VSX-D511 Receiver

1 Answer

Displaying....DSP NG can some one please help? some kind of error.


In my experience, NG on a system made in Japan means "No Good" (error). NG might stand for something else, but regardless, it sounds like an internal issue with the amp.

Sep 24, 2015 | Pioneer VSX-D510 Receiver

1 Answer

I spilled a liquid in my jvc rx-502ov receiver and a message reads dsp micom ng what do i do?


You fried the poor thing to put it mildly, Get a different one end cut down on your partying ,(GUY) Unless you have money to burn

Dec 05, 2012 | JVC Rx 5020v Stereo Receiver

1 Answer

Code f28


Hi, the error code F28 means one or both of these parts are bad.
  • Motor Control Unit (8540135)
  • Microcomputer Machine Control Unit (8540788)
It would be a good idea to order both, as both components have been problematic for error code F28. If you find either the MCU or the CCU(Microcomputer Machine Control Unit) fixed it.

Oct 02, 2010 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

JVC RX-6042S shuts down after 5 seconds


It will be one of the transistors that regulate the lower volatges (5V, 12V...)
I ffixed mine. the heatsinking on those transistors is pathetic, and its no wonder they dont last.
Mine was the 5V circuit, which also supplies the DSP board. so if you are getting a DSP NG, that could be that as well.
Check Q1434 and Q1404. if one is faulty, it drags the other one down with it.
Good luck.

Dec 27, 2009 | JVC RX-6042 Receiver

1 Answer

Flashing lights


HI, this is a control fault that may be corrected by unplugging or shutting down the breaker switch for about five minutes. this will reset the microcomputer to its original state. after the five minute reset, plug or switch the machine on and observe the results.

If the unit is still blinking and the unit is not operational, this will confirm a major control fault and you will need to replace the control board(microcomputer/timer control)

May 18, 2009 | Ariston Technologies Washing Machines

1 Answer

JVC A/V Receiver RX 7042S - DSP NG


it seems the problem of your unit is in the power amplifier section,the IC chip there is defected that why only analog source .you better bring back to them the unit it is the only option, that is there back job...

Jul 03, 2008 | JVC RX-6042 Receiver

1 Answer

JVC RX 6042


just google jvc go to customer service at the bottom look up manuals and u can print it right off the internet no cost

Apr 02, 2008 | JVC RX-6042 Receiver

Not finding what you are looking for?
JVC RX-6030V Receiver Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Audio Players & Recorders Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

The Knight
The Knight

Level 3 Expert

74459 Answers

 Grubhead
Grubhead

Level 3 Expert

5190 Answers

Are you a JVC Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...