Question about Whirlpool Ultimate Care II LSQ9549L Top Load Washer

1 Answer

Whirlpool washer Perminant Press cycle does not work

When using my washer on the Perminant Press cycle, it stops working after the drum fills with water, then the timer makes an unusually loud noise. To get it to continue working I am able to utilize the Normal wash setting.
Since this has started I've washed everything on Normal, but I am confused as to what could be causing an issue for only one cycle type.
Any suggestions/ideas?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Your timer is causing the problem more than likely, valves , pump motor is working so your timer itself is not change it most of the jobs can be done by the homeowner they are a quick connect disconnect and maybe a screw or a catch holding it just look at it how it attached to the console and reattach it the same way

Posted on Aug 12, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: LTE6234 Whirlpool Twin Thin Timer Broken?

The problem I have with my Whirlpool ThinTwin is that when I pull the washer knob the water does not start filling even though there is water in the apartment unit. The dryer works so i know there is power and not a circuit breaker issue as I have checked that as well.

When I turn the knob and pull in any position nothing happens. Any suggestion would be greatly appreciated.

Posted on Feb 03, 2008

jsrock516
  • 5911 Answers

SOURCE: Whirlpool Ultimate Care II Quiet Wash - Wash Cycle not holding water

Since your washer worked fine while in Germany and now is exhibiting this problem at your new home, you may want to double check how it was installed. I suspect you may have a problem known as "siphoning". The following link explains:

http://www.fixya.com/support/r587481-prevent_washer_siphoning

This could be a simple situation where the drain line on the washer is not installed correctly. There are minimum height and length requirments on the drain line. In addition, make sure the stand pipe you have the drain hose inserted in has a proper air gap to allow draining. All of this is explained in the link provided.

I hope this information is helpful to you. The majority of the situations arise from improper installation and is not an operaitonal problem with the washer. If, however, you double check everything and still have problems, please post back and let me know.


Posted on Sep 11, 2008

keithd2704
  • 56 Answers

SOURCE: whirlpool washer ultimate care II lsq8500JQ1 top...Problem

Ok folks to change the lid switch on these and many top loading Whirlpool, Maytag, Kenmore, etc is quite easy.

Steps to replace the lid switch:

1. Remove unit from AC.
2. Remove the loading door from the unit, or using some duct tape tape it closed.
3. Using a small flat bladed screwdriver find the 2 release catches on the front of the unit between the top cover and front panel. These are just snap claps to hold the top cover down. To release the top you will need to compress the latch using the screwdriver. Start with one side, then the other. Once you have released both clips the lid will lift up just like the hood of your car.
4. You will now be able to remove the lid switch from the unit.
5. Install the new switch and close the hood of the unit.
6. Test the repair by running the unit though a complete cycle.

A great place to order the replacement part for the unit is:

www.appliancepartspros.com

They ship same day on orders placed before 3pm EST. Overnight shipping is available, however I usually opt for the 2-3 day ground shipping and save the money.

If this switch replacement does not take care of the problem, you might need to replace the control board located under the front panel. This replacement is also very easy and takes about 10 min from start to finish.

Hope this helps everyone. Cheers,

Keith

Posted on Oct 21, 2008

michiganfan9
  • 179 Answers

SOURCE: Whirlpool Washer - Imperial Series Quiet Wash 2

your washers drain hose is too far down the drain pipe which is causing a siphoning action pull the washers drain hose out pipe some you should be able to hear water dropping into the pipe the reason it only happens in the rinse cycle is because the water from wash is being drained and before the water vacuum is broken the rinse water comes in causing it to keep draining

Posted on Dec 30, 2008

  • 97 Answers

SOURCE: Whirlpool washing machine makes grinding noise

Hello Friend, Your solution is a real quick fix. The problem you are having is very common, your motor coupling has broken and that is what's making the grinding sound, also in this condition it will always pump out the water. Go to your local appliance parts store and purchase a new motor coupler, your cost should be under $25. It's very simple to remove old and install new coupler. First remove two screws from control panel and tilt control panel backwords exposing area under panel. You will see a metal clip on each side of cabinet under panel. Remove these clips, and unplug wires from plug in on cabinet. Remove cabinet by lifting up in back and tilting forward. Once removed you will see the innerworkings of your washer. Lay washer on it's back and remove the two spring clips that hold water pump in place and remove water pump. Leave water pump hooked up just move to side out of your way. Then you will remove the two screws that hold the motor clips in place and just snap the motor clips off. Be sure to unplug the wire harness plug from the motor. Just simply lift the motor straight up and off of the transmission. There you will see the motor coupler broken and to replace, just pry old one off transmission and motor with large flat head screwdriver. You will notice that one half of coupler is attached to the motor and the other to transmission. In the coupler kit you will receive both pieces and the rubber center connector. Just replace all the old with all the new and your problem will be solved. Happy to help, Tim.

Posted on Jun 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whirlpool duet washer fills with water (maybe overfills) then stops and the wash light flashes an 8 then 1 type sequence


Hello, we are sorry to hear that you are experiencing this problem. We would recommend having a certified technician out to take a look at the Washer and give the appliance a proper diagnosis. If you would like further assistance you can send your name, phone number, address, model/serial number and the date of which you purchased the Washer to Whirlpool_Reviews@Whirlpool.com.

Apr 18, 2017 | Whirlpool duet Washing Machines

2 Answers

Whirlpool washer WTW57ESVW0 won't fill with water. I bought this machine two months ago was working fine and then just stopped filling water. Spin cycle and drain cycle work but it won't start fill...


Solution for WTW57ESVW0 Whirlpool Washer that won't fill or agitate, but will spin and drain water.

Replacing the Auto Load Sensing Switch (W10177795 - Illus. No. 12 on Control and Rear Panel Parts) fixed the problem.

In addition, a defective switch can also cause the machine to start agitating while it is filling.

It is relatively easy to replace and there are online videos that can help with the replacement.

Oct 27, 2010 | Washing Machines

1 Answer

Water drains during wash cycle. I have used this washer for many years without a problem. About two months ago I noticed that the water level in the drum was going down during the wash cycle. Last week I...


Take the drain hose out of the drain pipe and put it into a sink to test the machine

If that works make sure that the drain hose is being allowed to breath (ie let air into the main drain pipe so that the machine does not set up a syphon).

Jul 16, 2009 | Whirlpool Washing Machines

1 Answer

Whirlpool Model LSR8233EZ1


Transmission gearing failed or coupling.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for helping with your FREE question

Jan 11, 2009 | Washing Machines

1 Answer

Whirlpool LSW9750PW3. The washer has an intermittent problem. When it works it works great. When it malfunctions (using permanent press cycle), the washer will fill up and then the timer will stop...


sounds like motor contacts in timer may not be closing properly motor is trying to start but with contacts not right it overheats and shuts off ..also may be motor start switch that is where the wires connect to motor also ckd motor connector closely to may sure there is no loose connection between it and motor connections

Jul 25, 2008 | Washing Machines

1 Answer

Calypso - water goes straight to drain hose-not drum


the hose may still be filled from last cycle. try to put machine in final spin mode where all water from previous wash will be spun out the drain hose. once a siphon is started it can only be stopped by introducing air into the drain hose.

Sep 16, 2007 | Whirlpool Calypso GVW9959K Top Load Washer

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9549L Top Load Washer Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...