Question about Stanley Measuring Tools & Sensors

Open Question

Stanley fatmax stud sensor instuctions - Stanley Measuring Tools & Sensors

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 122 Answers

SOURCE: How to basically operate my

Press the red button - (distance) you will see a red dot on the wall you are measuring - then you will hear a beep - release the button and read the display - the measurement should be displayed and accurate within a quarter inch.

Posted on Nov 23, 2008

  • 1 Answer

SOURCE: Just purchased a Stanley FatMax 10-778 retractable

1. Make sure the side lock is unlocked.
2. Push the thumb tab all the way to the front of the blade handle.
3. Insert the blade in the opening, you may notice two notches on the top side of the blade.
4. Press the small blade release button as you slide the blade into the knife. You may have to jiggle up and down to get the two notches on the blade fully into the handle.

If properly inserted, the exposed area of the blade should look very close to an equilateral triangle.

make sure both notches of the blade are inside the handle. They notch into the thumb lever.

good luck

Posted on Apr 11, 2010

Testimonial: "Thanks so much!"

nielsonplumb
  • 91 Answers

SOURCE: I have a stanley FatMax. How do I insert the blade

On the side there is a big gold wheel, twist counter clockwise and the case should split in half, the blade is held by a magnet, prise the old blade off and replace with new one, then put case back together and tighten gold wheel clockwise
Goodluck!

Posted on Mar 07, 2011

  • 436 Answers

SOURCE: Need a Stanley FatMax TLM100 manual. Where can I

Easy enough. Here is the link:

http://www.laserstreet.com/documents/TLM100_manual.pdf

Hope this helps

Thanks

Please rate FIXYA

Posted on May 20, 2011

Testimonial: "Thanks for the fast response. Just what I needed."

  • 1015 Answers

SOURCE: my stanley stud sensor 200

Without knowing what room you are using it in it could be a underlayment of wire mesh that you are reading. If it is an older home this was used often as a backing for plaster instead of lath.Thank you.

Posted on Jun 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I calibrate a FatMax digital level?


Mark, Automatic calibration, check the little pockets on case instructions inside, the instructions show how.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Stanley FatMax Digital level mp4

Stanley fatmax digital level instructions Measuring Tools Measuring Tools

STANLEY HAND TOOLS Measuring Leveling Layout Levels Stanley FatMax Digital...

http://www.microprecision.com/equipment/STANLEY-CALIBRATION.html

Mar 04, 2016 | Measuring Tools & Sensors

1 Answer

How can I get a parts repair manual/list for a stanley fatmax 3.8 cfm compressor


try searching for stanley fatmax compressor . I think bostitch owns it

Nov 03, 2014 | Measuring Tools & Sensors

1 Answer

Instructions stanley fatmax staplegun


Don't know what model you have but these instuctions should be pretty typical.

PHT350 Hammer Tacker Instructions

Aug 18, 2014 | Measuring Tools & Sensors

1 Answer

Stanley fatmax s300 manual


Go to http://www.youtube.com/watch?v=QInszVD9WpE&feature=youtu.be - doesn't tell you everything, but better than the manual Stanley ship with the product, which is just a collection of hard to decipher graphics.

Feb 03, 2013 | Stanley Measuring Tools & Sensors

1 Answer

Can't close stanley fatmax


It only goes in one way, try to loosen the screw a little

Jul 30, 2012 | Stanley Fatmax Xtreme Retractable Utility...

1 Answer

Instruction for Stanley FatMax Stud Sensor Finder 400 (77-730)


Please people dont waste your money but a cheap standard one Stanley 77-730 stud finder is bad does not work at all , miss my old cheapy never failed me

Mar 05, 2012 | Stanley Measuring Tools & Sensors

1 Answer

I am looking for a manual for the Stanley Intellilaser Pro 77-500


I downloaded a manual for my Bostitch (stanley) framing nailer yesterday from their webpage. You should be able to find one somewhere on stanleys home page.

Apr 21, 2009 | Stanley 77 500 Intellilaser Pro Stud...

1 Answer

How to basically operate my stanley fatmax, TLM100. The directions that came with it were for another Stanley product. Thanks,Ralph


Press the red button - (distance) you will see a red dot on the wall you are measuring - then you will hear a beep - release the button and read the display - the measurement should be displayed and accurate within a quarter inch.

Nov 16, 2008 | Stanley 100 ft. Tape Measure, FatMax

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Stanley Measuring Tools & Sensors Experts

Lawrence Oravetz

Level 3 Expert

9587 Answers

Steve

Level 3 Expert

3287 Answers

john h

Level 3 Expert

12104 Answers

Are you a Stanley Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...