Question about Standard (CRT) Televisions

1 Answer

TV turns itself off.

Hi there,
My TV is usually left on standby, when I turn it on it will stay on for a few minutes then without warning turn off.
When it turns off an orange blinking light starts (next to the red standby light) which has printed above it ON TIMER.
At this point I can't turn it on at all.
The only way to get it to work again is to turn it off completely and let it rest, then push the power button and standy light comes on, but it will shut down again shortly after you turn it on, with the same blinking orange light.

Posted by on

  • Kozzi Oct 24, 2008

    Gee what insight....as helpful as a kick in the balls!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 252 Answers

If you now how to used soldering iron , resolder your tv

Posted on Oct 22, 2008

  • jose jeo patalinjug
    jose jeo patalinjug Nov 01, 2008

    just try to re solder you tv. coz 50% problem of tv is lose connection ,but be careful of short circuit

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toshiba 27af45 repeatedly turns itself off. Sometimes (usually) every few minutes, other times will stay on for hours. Works perfectly otherwise.


The fact that the television stays on for hours and other times turns in five minutes shows that your problem is intermitent .A defective component in the power supply is probaly causing the B plus voltage to go up.The TV can also have a dry joint which looks more likley i am curtain if you gave the TV a firm tap to the side when it come off it would come on back. Try it .

Dec 29, 2010 | Toshiba 27AF45 27" TV

1 Answer

Canno turn the tv on.


You probably have a main or high voltage power supply problem; the latter produces the 20,000 plus volts for the CRT and gets its voltage from the main supply. It's difficult to say which is at fault without a few measurements.

Feb 14, 2010 | Sony FD Trinitron WEGA KV-32HS420 32" TV

1 Answer

Sstandby light blinks & doesn't turn on.


Unplug TV from the power outlet and let it sit for a few minutes, then plug it back. It sould work normally after that.

Apr 28, 2009 | Sony FD Trinitron WEGA KV-36XBR800 36" TV

1 Answer

TV keeps turning itself on and off, onto standby


I managed to find a local repair man who fixed the problem. He put in a new transformer.

Dec 01, 2008 | JVC AV-32D305 32" TV

1 Answer

Sony Wega kv27FV310 standby flashes 2 times with no picture or sound


3 years ago, i had the same problem with a samsung 36", when i switched it on it would stay on for around half an hour, i tried to switch on straight away, but it wouldnt, i had to leave it for an hour or so, then it would stay on for about 5 minutes. And the same thing the next day (half an hour then 5 minutes). I left it into the repair shop, it had to get a circuit board replaced at a cost of £315, dont know how much it will cost to get fixed now, as i could buy the same tv for a little over that now.

Apr 14, 2008 | Sony FD Trinitron WEGA KV-36FS120 36" TV

2 Answers

Standby relay clicks on and off continusly. Tv won't turn on. I check my diode and transistor who control the standby relay and it is fine. I also replaced the flyback and I still in the same situation....


Hi there!

You have an obvious error state on the unit. You may want to try and remove the Line Transistors to check for voltage first. In the region of 145V(between base and collector. If the set then stays in standby you may have a vertical error. Also check 5V rail to the processor and suspicious looking components like caps. Good Luck,JUS004

Mar 05, 2008 | Sony KV-27S15 27" TV

1 Answer

GE 31GT740 clicks off and on


Dead, led flashing red/green at first, then going to red standby
Replace C604 (1000uF, 16v) elec. cap. It is in the decoupling circuit for the 5 volt supply
Reverts to standby from switch on via TV or Video
No 5v rail because FET MTP3055 o/c. (BUZ71 will do nicely)
Goes straight to standby, after a quick burst of power
Replaced R952 (39K), had gone slightly high

Nov 23, 2007 | GE 31GT740 31" TV

1 Answer

The flashibg red light


John, I do not know of a code, but it is a good idea in the design to have several goes at starting a circuit, before completely shutting it down. Oscillators are supposed to self start due to noise generated. Some electronic circuits require a reset pulse to be generated before the start up is allowed. The reset circuit may not be generated if the set is turned on again too soon, so it will stay in standby. This may normally be a few minutes to 30 minutes so it seems something in your set is faulty and could get worse. Try a test run with the back off and clean it out of dust with a long brush to keep it cooler. Make sure little fingers cannot get near it. Look to see if anything is obviously overheating.

Oct 21, 2006 | Thomson 24WK25U 24" TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68223 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...