Question about Panasonic DVD-RV31 DVD Player

12 Answers

DVD not playing message say H02

We are unable to use the DVD as the following message comes up on the screen. "HO2". We have had a look in the manual and the manual says "the number following H depends on the status of the unit". We have tried resetting the unit, however, it is still not working. We would appreciate some advice. Many thanks.

Posted by on

  • Jazz66 Mar 23, 2008

    Will not play DVD's and get the error message H02

×

Ad

12 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 215 Answers

There is a solution but it takes a little care because the wrong thing touched will give you a shock. Just stay away from the unit near where the power lead enters the unit. OK. remove the top of the unit, place a disk in the unit press play and gently give the DVD a gentle push in a clockwise direction. This disk should then get up to speed and start playing. It also unlocks the error. No guarantees with this one some work, some don't. I hope yours does. BMW

Posted on Jul 28, 2006

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

This answer worked for me on the first try. Thanks!

Posted on Apr 23, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I did just like you said. Oh Master! and it works.... just remove the top of the unit, place a disk in the unit press play and gently give the DVD a gentle push in a clockwise direction

Posted on Mar 05, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same Error Code: H02. Great Fix. Remove 2 screws on the left, 2 screws on the right, and 3 screws on the back. Gentlely remove the lid, spin the center spindle, carefully plug in and test. Replace lid and enjoy. Works like a charm!

Posted on Oct 30, 2012

Ah, good stuff. It took me three tries before it seemed to catch, but it eventually worked. Guess I'll keep the screws out of the lid. Haha.

Posted on Jan 12, 2008

Worked perfectly..........many thanks

Posted on Nov 20, 2007

THANK YOU SAME PROBLEM GREAT SOLUTION

Posted on Nov 07, 2007

My flywheel would not spin with my finger or a screwdriver. so i opened the top. there is a very easy moving thing on the top. tried that. didnt work. going to check to see if i can get under it to get the other thing moving.

Posted on Jun 10, 2007

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wow! Are we all having this problem at the same time? Must be we're at the end of the life of this DVD player. Thanks for your suggestions - I'm off to see if it works.

Posted on Mar 19, 2007

I was unable to clear the HO2 error without removing the lid. I opened the top and ever so slightly rotated the wheel. Off it rotated and now we're watching movies and having a great time; at least until it stops again.

Posted on Mar 11, 2007

I just tried Guests' solution and had a little trouble. But after I 'gently' moved the wheel I got nothing. But with a screwdriver and a little pressure to the wheel it seeed to work perfectly. I guess this might prolong the enevitable new player a few more days anyhow.

Posted on Jan 10, 2007

I was able to clear the H02 error without removing the lid of the unit. Just open the disk tray and gently turn the ratcheted wheel clockwise with your finger. Then load the disk and it should read OK.

Posted on Jan 08, 2007

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the oxygen sensor


Removal & Installation Upstream HO2 S1 To Remove:
NOTE: If the engine temperature is lower than 120 °F (48 °C), the HO2 S1 sensor may be difficult to remove. Excessive force could possibly damage the threads in the exhaust manifold.
  1. If necessary remove the fuel injector cover.
  2. Disconnect the HO2 S1 sensor electrical connector.
  3. Using an oxygen sensor removal tool carefully remove the heated oxygen sensor.
To Install:
  1. Coat the threads of the oxygen sensor with anti-seize compound
  2. Install the HO2 S1 sensor. Tighten the HO2 S1 sensor to 30 ft lb (41 Nm).
  3. Connect the HO2 S1 sensor connector.
  4. If removed, install the fuel injector cover.
Downstream HO2 S2 To Remove:
NOTE: If the engine temperature is lower than 120 °F (48 °C), the H02 S2 sensor may be difficult to remove. Excessive force could possibly damage the threads in the exhaust pipe.
  1. Raise and safely support the vehicle.
  2. Disconnect the H02 S2 electrical connector.
  3. Using an oxygen sensor tool carefully remove the H02 S2.
To Install:
  1. Coat the threads of the H02 S2 with anti-seize compound.
  2. Using an oxygen sensor tool install the H02 S2. Tighten the sensor to 30 ft lb (41 Nm).
  3. Connect the H02 S2 sensor electrical connector.
  4. Lower the vehicle.
prev.gif next.gif

Oct 07, 2010 | 2001 Buick Regal

1 Answer

H02


The HO2 message means the disc is not spinning,it's not about the lens
or the laser.It is easy to take the lid off.Once you do that,plug it in,open the tray with the remote,put in a DVD,close the tray and then give the white plastic wheel on the top a gentle little nudge to get the disc spinning.

Jan 30, 2010 | Panasonic DVD-LS50 Portable DVD Player

1 Answer

It wont read any disks and keeps coming up with DVD HO2 i've unplugged it for a while but it still comes up with the same message.


POSSIBLE solution

I had this problem a while ago comes up with that code then NO PLAY there are 5little discs inside that seperate the discs when theyre inserted these had come loose somehow I simply restacked them on the spindle, however they MUST go in a certain order or H02 will still appear, mine had numbers on them (but NOT consecutive) I just stacked em in ascending order. It worked great after that.
HOWEVER Ive just had the same problem again but the discs arent loose this time.

Mar 10, 2009 | Technics SC-DV290 System

1 Answer

Pana sonic home theater system Ho2 code


the problem be in the spindle motor drive circuit so you can solve it

Dec 24, 2008 | Panasonic Home Theater System System

1 Answer

Technics sc-dv290


i once had a panasonic dvd player which displayed the same code H02 and used the same drive mechanism as your player. this turned out to be a worn spindle motor and once replaced, all worked fine. you may well have the same fault. hope this helps?

Oct 26, 2008 | Technics SC-DV290 System

1 Answer

Discs cant be played..


More information:

Your DVD HO2 error problem appears to be Panasonic specific: Go to this link:
http://www.hardwareanalysis.com/content/topic/55214/

Feb 11, 2008 | Panasonic SC-HT880 System

3 Answers

Panasonic DVD-RP56 Error H02


I read about removing the cover and spinning the motor by hand. It was suggested without power. I found that I had to have the unit powered up when I hand-spun the motor, then everything worked perfectly... we'll see for how long.

Feb 10, 2008 | Panasonic DVD-RP56 DVD Player

1 Answer

HO2 error


That's the spindle motor and it has to be replaced to solve the problem.

Jan 01, 2008 | Panasonic DVD-RV26 DVD Player

11 Answers

Error Message H02


I have had this problem on numerous times. Once while in warranty. Discussed with technician and he reported that the gears get dirty and stick and need cleaning. Since last year, I get this message every 3-4 months. I take out all the screws from the bottom, open the cast carefully, and use some canned air, clear all the gears, gently rotate all of them. Put everything back together and should work fine.

Dec 25, 2005 | Panasonic DVD-LX9 Portable DVD Player

Not finding what you are looking for?
Panasonic DVD-RV31 DVD Player Logo

2,678 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5342 Answers

Demonic-2011
Demonic-2011

Level 3 Expert

508 Answers

The Knight
The Knight

Level 3 Expert

75169 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...