Question about Printers & Copiers

2 Answers

Error code M1 appears and how to clear it . M2 is ok easy to clear.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

C03ff

Posted on Feb 27, 2014

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 145 Answers

How to clear an M1 code.
Solution:
To clear an M1 code, go to Counter/Maintenance/Maintenance Set and press the Clear key.
hope that help

Posted on Nov 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code 5102 on konica minolta c253


According to the service manual, Code: C5102 Code C5102 Description Transport motor's failure to turn
• The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. Remedy 1 Check the M1 connector for proper connection and correct as necessary. 2 Check M1 for proper drive coupling and correct as necessary. 3 Check the PRCB connector for proper connection and correct as necessary. 4 M1 operation check. 5 Change M1. 6 Change PRCB.
The technical sites say that there is probably a paper jam. If the jam is cleared but the error persists, the transport motor will probably need to be replaced. This motor has a pretty high failure rate. A qualified copier technician should be able to change it out in 30-60 minutes.

Aug 30, 2015 | Konica Minolta Printers & Copiers

1 Answer

How to remove error code M2


question too vague.
make? model?
example:
Re: Konika Minolta BizHub 163 - Error Code? M2
• To display the count of the supplies life counter.
When the counter reaches "0", life 1 will be detected and maintenance call M2 will appear.
The initial value is 40,000, and the countdown system is used.
Use Setting/Procedure
• To clear the count, use [CLEAR DATA] of the Service Mode.

Jun 06, 2015 | Printers & Copiers

1 Answer

What is solution for konicaminolta 164 maitanance call m2


M2 Call service.Maintenance M2, M1 Call service errors.To remove this error do the following steps.
1-Press utility button on panel.
2-Now press these buttons one by one, Press Stop, then zero, again zero, then stop,then press zero.
3-its the code to get into service mode.
4-After pressing above mentioned buttons you will enter into service mode.
5-Now select service choice option.select it by pressing OK button.
6-In service choice option you will see Maintenance count option.
7-Select it by pressing Yes or OK button.
8-There will be three options 0,1,2.
9-Select 1, it will show a new menu, with numbers, now press C button to clear the counter.After the counter is cleared.Select 0 and press Reset button.

Jul 04, 2014 | Konica Minolta bizhub Printers & Copiers

1 Answer

Me problem is code c03ff


Hello by mistake you have changed the copier model ..
hi...this error code appears after you clear the data in service mode...so you have to enter sevice mode
Utility+stop+0+0+stop+0+1....enter to ADJUST &specify the speed model from the table find 21-18-16
select the model you have

Feb 27, 2014 | Konica Minolta Printers & Copiers

1 Answer

How to solve M2 in bizhub 164


Konika Minolta BizHub 163 - Error Code M2
Press the Utility button,
then Stop 0 0
then press again Stop 0 1
then scroll to Clear Data, and then Supplies Data and clear.
You must be aware that clearing this counter clears the drum, developer and other counters.

Feb 23, 2014 | Minolta bizhub 200 All-In-One Printer

1 Answer

M1 m2 m4 screen messaege


Utility button then stop 00 stop 01. Then use arrows to clear data screen then clear counters. Has the drum and developer been replace do that before clearing the counters

Jan 12, 2014 | Minolta bizhub 180 Black and White Copier

1 Answer

Minolta DI1611 M1, M2


replace the drum cartridge, also clear maintenance counters in service mode

Dec 23, 2013 | Konica Minolta Printers & Copiers

3 Answers

How can i reset m2 bizhub 211


I Have a Konika Minolta bizhub 211. I had been trying this solution for repairing m2 call. but the code is appear till now. anyone help me. please give me solution step by step.
Thanks

Mar 05, 2011 | Sharp AR-5320 Black and White Copier

2 Answers

Maintenance M2 call service


M2 Call service.Maintenance M2, M1 Call service errors.To remove this error do the following steps.1-Press utility button on panel.2-Now press these buttons one by one, Press Stop, then zero, again zero, then stop,then press zero.3-its the code to get into service mode.4-After pressing above mentioned buttons you will enter into service mode.5-Now select service choice option.select it by pressing OK button.6-In service choice option you will see Maintenance count option.7-Select it by pressing Yes or OK button.8-There will be three options 0,1,2.9-Select 1, it will show a new menu, with numbers, now press C button to clear the counter.After the counter is cleared.Select 0 and press Reset button.

Dec 17, 2010 | Minolta bizhub 180 Black and White Copier

2 Answers

Konica Minolta bizhub 210 error m2 appear on display


Hi
You can reset (M2) by reset clear data
Enter to service mode By Pressing :
Utility - clear -0 - 0 - clear -0 - 1
Press ADJUST
Press CLEAR DATA
Turn OFF Copier and Switch it ON

Feb 28, 2010 | Konica Minolta Printers & Copiers

Not finding what you are looking for?
Printers & Copiers Logo

Related Topics:

439 people viewed this question

Ask a Question

Usually answered in minutes!

Top Printers & Copiers Experts

kakima

Level 3 Expert

96627 Answers

old marine
old marine

Level 3 Expert

1476 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...