Question about Samsung TXG2746 27" TV

1 Answer

Tech :Gil Scott Samsung problem:please help

Tv comes on when powered up, but then flashes on/of by itself.
Set goes of when you turn the volume up or down then comes back on by itself.
No control over volume

Posted by on

  • 1 more comment 
  • Anonymous Nov 28, 2008

    kkk

  • stingelhoff Jan 05, 2009

    same problem

  • darryl b Jan 13, 2009

    I have the same prob it hapened when I un pluged it when it was on.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 46 Answers

Hi gil
sounds a bit weird it could be a processor problem
cheers grant

Posted on Oct 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lcd tv light flashing but no picture or sound


If you removed power by turning off power itself to the set instead of turning it off by turning the set itself off---that is not a good thing to do.

When power is restored a surge can and likely hit the power supply in your set---time for a tech or shop to open it---I suspect they will find the standby or main power supply is damaged or now bad.

Dec 06, 2012 | Bush Televison & Video

2 Answers

Wont turn on. Jensen TS2750J


For a dead tv with a flashing menu led

Replace diode UD305 with NTE580 to improve reliability,and replace resistor R307, 1 ohm @ 1 watt

hope this fixes it, if not let me know

Mar 22, 2008 | Jensen TS2750J TV

1 Answer

Volume pegs to max. Turns itself on. Goes to menu. Intermittent


This is becoz your Internal Remote control response program chip needs to be replaced! You need it to get repaired at nearest service station. Or it may be due to Your keys pressed continously from remote control. Check both the causes! then decide. It will help you!

Dec 23, 2007 | RCA F38310 38" TV

2 Answers

Volume decreases by itself


maybe defective speaker or audio output ic or shorted capacitor within audio circuit

Nov 09, 2008 | RCA F32648 32" TV

1 Answer

32" No Power, But Beeping Sound


you have a problem with the power supply module . it is located on the main board and needs to be replaced by a local repair tech.

Aug 31, 2008 | Zenith C27V22 27" TV

1 Answer

RCA 32" keeps turning on/off on its own


The most common problem with shut down on this model is the HVT drifs. In short, you need to set the G2 to 290v, with no signal and a blue screen. If this is to + or - 5 volts set will shut down after 10 to 15 seconds. If this does fix your set, its a sign HVT is going out. I wouldn't advise repair of this set. Its not worth it.

Tvman

Jul 31, 2008 | RCA 32V420T 32" TV

1 Answer

Volume goes full blast when turned up from zero to just a "1" onscreen


I have seen a similar problem. get to design mode (that trick with the remote mute & the set menu button) & look for a data address in the audio section that is set to all (F)s. sorry i can't remember the exact address. you could always just guess just make sure you write down where they are currently set .
Hope this helps.

Jan 25, 2008 | Toshiba 19A26 19" TV

1 Answer

Need help


this is only due to loose contact in power supply or there is a print intermittent in power supply.

as tv is on so no possibility of any parts failure.

if you are not tech person take the help of tech person.

good luck.

 

Oct 12, 2007 | RCA 24F512T 24" TV

1 Answer

TV Turned itself off and on with flashing green power button


If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box
connected.

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from PartStore.com

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |


On LCD Pay particular attention at inverter and power board, power board can be inspected looking for bulged or leaking capacitors, then tested with a multimeter. The inverter is more difficult to test , there is need to read voltages, should be done by a tech. Also the LCD controller board can cause same problem

On Plasma, test Sustain (Ysus/Zsus) / Buffer boards , cables to plasma, digital board and power board.

On Rear Projection : check lamp, lamp ballast, power board, and convergence.

On CRT TVs, check ballast , flyback transformer, CRT, Tuner, Convergence.

Sep 03, 2007 | RCA F27718 27" TV

1 Answer

KV 27S65 Sony Trinitron 27"


So far you have done all you can and you have done everything right. The fact that the TV turned off by itself and then turned back on by itself suggests that one or more solder joints have come loose inside the set. A qualified tech should find this easy to fix, and Sony sets are always worth repairing, so it is now time to have the set serviced by a tech experienced in Sony standard sets.

Sep 01, 2007 | Sony KV-36XBR400 36" TV

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Televison & Video Experts

The Knight
The Knight

Level 3 Expert

69570 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

cce772000

Level 1 Expert

7 Answers

Are you a Samsung Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...