Question about Kenwood KDC-PSW9524 CD Player

2 Answers

Can't enter the code : 4 waiting displayed

I put the code in wrong 4 times (Idiot)
now it won't take the code at all, just gets 4 waiting once i try to enter it.
Andy

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 65 Answers

You must leave your radio in power on for an hour just to clear the wait, after that only you are able to reenter your code. make sure do not power off the radio, or else every time you power on you still have to wait for an hour to clear it.

Posted on Aug 08, 2014

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Typically if you enter the wrong code several times the unit will lock up. To unlock it you need to leave the radio on for at least 30 to 60 minutes and that should allow you to re enter the code.

Posted on Oct 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a blaupunkt woodstock dab 54 and its stuck saying wait 1h HELP!


by default you have 3 chances to enter your code, after then time is get much longer for you to wait. what you can do is still keep your radio power on and leave it for 1 hour, Do not power Off. the cycle of wait will reset. then you can try enter you code again. hope its help.

Aug 02, 2014 | Blaupunkt Woodstock DAB 52 CD Player

4 Answers

Kenwood KDC-319 code needed


It is the anti theft code, you need to get the code, I will see what I can do.

Apr 02, 2008 | Kenwood KDC-319 CD Player

1 Answer

Entered code display now reads waiting 2


must be careful, if you already make a 2nd try. most the 3rd try if the code again wrong. then the next wait time will be more longer to reset the wait. make sure the radio is remain on.

Jan 05, 2011 | Kenwood KDC-PSW9524 CD Player

1 Answer

I have the code but only says on screen that it is waiting? on my kenwood kdc 6090r


• Security-related information

1. Forced Power ON mode (All models)

Even when the security (Mask key) is approved, resetting

the unit while holding the ATT and Preset 4 keys makes it

possible to turn the power ON for 30 minutes. After 30

minutes have elapsed, it is not possible to return to the

previous condition unless the unit is reset again.

2. Method of registration of the security code after EEPROM

(Tuner Unit ***'y) replacement

(Code security model)

(1) Enter the test mode. (See " 1. How to enter the test

mode")

(2) Press the CLK key to enter the security registration

mode.

(3) Enter the code using the Preset 1/2/3/4 keys.

Example: To enter "3510"

• Press the Preset 1 key 4 times.

• Press the Preset 2 key 6 times.

• Press the Preset 3 key twice.

• Press the Preset 4 key once.

(4) Press and hold the DISP key for 3 seconds until

"APPROVED" is displayed.

(5) Exit from the test mode. (See " 2. How to exit from the

test mode")

(Note) All Clear is not applicable to the security code of

this model.

3. Simplified method of clearing the security code (K Type

only)

(1) While the code entry is requested, press and hold the

VOL UP key for 3 seconds while holding the DISP

key pressed. (This should turn "----" off.)

(2) Enter "KCAR" from the remote. (Same way as the 00

model)

Press the 5 key on the remote twice, then press the

Track Up key. (This enters "K".)

Press the 2 key on the remote 3 times, then press the

Track Up key. (This enters "C".)

Press the 2 key on the remote once, then press the

Track Up key. (This enters "A".)

Press the 7 key on the remote twice, then press the

Track Up key. (This enters "R".)

(3) The security code is cleared and the unit enters the

ALL OFF mode.

(4) If you commit a mistake in the code entry, the unit

enters the code request mode again.

4. Method of writing the Mask key while the EEPROM is in

the initial status

(1) Enter the test mode. (See " 1. How to enter the test

mode")

(2) Press the CLK key to enter the Mask key registration

mode. "TRANSMIT1" should be displayed now. The

display at this time should show " < > " in place of " [ ]

".

(3) Point the Mask key remote toward the light sensor,

and press and hold its key for more than 0.5 second.

(4) When "TRANSMIT2" is displayed, press and hold the

key on the Mask key remote for more than 0.5 second

again. The first and second counter codes are not

compared at this time.

(5) When "APPROVED" is displayed, the write operation

is complete. Now the demonstration mode is initiated

and the test mode is terminated.

(Note) In the same way as previous models, if 30 minutes

have elapsed with no code written, an error occurs

and the power is turned OFF.

5. Method of initializing the Mask key

(How to reset the unit from the Mask key approved condition

to the factory condition)

(1) Enter the test mode. (See " 1. How to enter the test

mode")

(2) "TRANSMIT1" is displayed and the Mask key entry

request mode is initiated.

The display at this time should show " ∗ ∗ " in place of

" [ ] ".

(3) Press and hold the key on the Master key remote for

more than 3 seconds.

(4) When "TRANSMIT2" is displayed, press and hold the

key on the Master key remote for more than 3 seconds

again.

(5) When "APPROVED" is displayed, the Mask key is

cleared, the demonstration mode is initiated, the test

mode is terminated and the unit returns to the factory

condition.

6. Method of clearing all Mask key-related data

(1) Enter the test mode. (See " 1. How to enter the test

mode")

(2) Press the CLK key to enter the Mask key registration

mode. "TRANSMIT1" should be displayed now.

(3) Point the Master key remote toward the light sensor,

and press and hold its key for more than 3 seconds

(until the level display shows the full condition).

(4) When "TRANSMIT2" is displayed, hold the key on the

Mask key remote for more than 3 seconds again.

If "TRANSMIT1" is displayed in place of "TRANSMIT2",

restart the procedure from step (3).

(5) When "APPROVED" is displayed, all security data is

cleared and the unit returns to the condition before
Mask key writing with the EEPROM in the initial status

Apr 05, 2010 | Kenwood KDC-6090R

1 Answer

How do i enter the code in a 98 polo radio?


Hi,

Once you have the unlock code, then turn on the radio. You should see SAFE displayed. After about 3 secs, "0001" should appear. Use the station preset buttons 1 thru 4. Preset 1 changes the first digit of the code, and preset 2 changes the second digit, etc. Enter all 4 digits of the code. After code is entered, press right side of "Seek" button for about 2 seconds, until an audible signal is heard. If you hose up and get the wrong code...will go back to SAFE displayed. You will get another chance to enter the code. After 2 failed attempts, you have to wait 1 hour again for it to unlock. So carefully enter the correct code the first time.

In case, problem persists, let me know.

Thanks.

Sep 07, 2009 | Car Audio Receivers

1 Answer

I have the code for my Krc-585 and have entered the code 5 times when "code" appears on the screen,Now it's just stuck on "waiting" with a 4 below it?I'm over waiting I want to crank this puppy!! thanks...


You are entering the wrong code ...that is why it is not accepting it and going into WAITING.

Unfortunately Kenwood codes are not available for free from anywhere on the Internet.

Main Dealer or Decoding Service only.

To rest the WAITING, leave it SWITCHED ON...UNDISTURBED for a couple of hours and it will automatically reset itself

Aug 02, 2009 | Kenwood KRC-38MR Cassette Player

1 Answer

Went to prison for 2 yrs. got out .car battery wasw dead,charged it, started my car and my stereo is asking for a code.all my pa`per work is gone,along with most everything else i had.all i have right now...


The unit can be used.
When the Security Code function is activated, the code can't be
changed and the function can't be released.
Note, the Security Code can be set as the 4 digit number of your
choice.
1 Enter Standby
Press the [SRC] button.
Select the "ALL OFF" display.
2 Enter Menu mode
Press the [MENU] button for at least 1 second.
When "MENU" is displayed, "Security"/ "SECURITY" is displayed.
3 Enter Security Code mode
Press the [4] or [¢] button for at least 1 second.
When "ENTER" is displayed, "CODE" is displayed.
4 Select the digits to enter
Press the [4] or [¢] button.
5 Select the Security Code numbers
Press the [FM] or [AM] button.
6 Repeat steps 4 and 5, and complete the Security Code.
7 Confirm the Security Code
Press the [¢] button for at least 3 seconds.
When "RE-ENTER" is displayed, "CODE" is displayed.
8 Do the step 4 through 7 operation, and reenter the Security
Code.
"APPROVED" is displayed.
The Security Code function activates.
When the wrong Code is entered in steps 4 through 6, repeat from
step 4.
Press the Reset button and when it's removed from the
battery power source
1
Turn the power ON.
2 Do the step 4 through 7 operation, and enter the Security Code.
"APPROVED" is displayed.
The unit can be used.

IF ALL ELSE FAILS TRY THE RESET BUTTON...
HERE IS A LINK TO KENWOOD WITH THE OWNERS MANUAL FOR THE MODEL YOU HAVE.


OWNERS MANUAL:
http://www.kenwoodusa.com/UserFiles/File/Global/Consumer/Manuals/KDCX569.pdf

KENWOOD WEBSITE:
http://www.kenwoodusa.com/Support/

GOOD LUCK TO YOU!!

Jun 25, 2009 | Kenwood eXcelon KDC-X469 CD Player

1 Answer

I have the code put it in still not working dont no how to put it in


NOTE: IF YOU TRIED UNSUCCESSFULLY TO ENTER YOUR CODE YOU MAY BE PROHIBITED FROM ANOTHER ATTEMPT FOR UP TO 24 HOURS. See below--section C

A. Input Security Code:
  1. Enter Standby: Press the [SRC] button. Select the "ALL OFF" display.
  2. Enter Menu Mode: Press the [MENU] button for at least 1 second. When "MENU" is displayed, "Security"/"SECURITY" is displayed.
  3. Enter Security Code mode: Press the [|<<] or [>>|] button for at least 1 second. When "ENTER" is displayed, "CODE" is displayed.
  4. Select the digits to enter: Press Press the [|<<] or [>>|] button.
  5. Select the Security Code numbers: Press the [FM] or [AM] button.
  6. Repeat steps 4 and 5, and complete the Security Code.
  7. Confirm the Security Code: Press [>>|] button for at least 3 seconds. When "RE-ENTER" is displayed, "CODE" is displayed.
  8. Do the step 4 through 7 step operation, and reenter the security code. "Approved is displayed and the Security Function activates. However, if you enter a code different from your security code you have to start over from Step 4.
B. After Pressing the Reset button or when removed from power source.
  1. Turn the power ON.
  2. Do the step 4 through 7 operation, and reenter the security code. "APPROVED" is displayed.
C. If an incorrect code is input, "WAITING" is displayed and the input prohibited time shown below is generated. After the input prohibited times lapses, "CODE" is displayed, and input can be done.

1 Time = 0 minutes
2 Times = 5 minutes
3 Times = 1 hour
4 Times = 24 hours

Here's a link to the manual:
http://manuals.kenwood.novenaweb.info/languages/EN/support/manuals/KDC-MV6521~6021~5021%20(EN).pdf

Apr 23, 2009 | Kenwood KDC-5021 CD Player

1 Answer

KCD-X590 is looking for a code that i never put in, and i bought the deck brand new


Method of clearing the programmable security
code (KDC-MP632U/X590)
1. While "– – – –" is being displayed, press [->> ] key for at
least 3 seconds while pressing [AUTO] or [TI] key.
This makes "– – – –" display disappear.
2. Using the remote controller, input "KCAR".
Press remote controller [5] key 2 times (Input for "K") and
then press [->> ] key.
Press remote controller [2] key 3 times (Input for "C") and
then press [ ->>] key.
Press remote controller [2] key once (Input for "A") and then
press [->> ] key.
Press remote controller [7] key 2 times (Input for "R") and
then press [->> ] key.
3. The security is released and the unit enters the STANDBY
mode.
4. If a wrong code is input, the unit goes into the Code Re-quest
mode.

Oct 14, 2007 | Kenwood KDC-X590 CD Player

Not finding what you are looking for?
Kenwood KDC-PSW9524 CD Player Logo

Related Topics:

362 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...