Question about Samsung Projection Televisions

1 Answer

When I turn on my samsung dvd-v70 (combination dvd/vcr) it stays on fo 10 seconds then turns itself off

Posted by on

  • powr40 Oct 22, 2008

    Hi Nova 1, thanks for the thought but the dew symbol doesnt appear and I have had the vcr plugged in for a few weeks and it still happens. If I listen very closely i can hear two faint clicks about two seconds apart before it turns off,

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 196 Answers

Does it display a dew symbol? dont turn it off at the mains when not in use the internal heater for the vcr part needs to be on to keep moisture away this may be why it turns off when you try to use it

Posted on Oct 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't my Samsung HL-R4667W DLP tv turn on?


Theres a cover on the back that is vented w/4 screws on like the corners,also theres a symbol that looks like a "T" on it,take that cover off and right behind the symbol "T" an arm like plastic piece is what hits a lever inside when then cover is installed ,flip that little blue lever up and down a couple of times with the set unplugged reinstall cover making sure the "T" is in the position to hit the lever and tighten not too tight.
if this don't work it may be your colorwheel.Good Luck!

May 27, 2010 | Samsung HL-R4667W Rear Projection...

1 Answer

Set won't stay on, won't turn on


Sounds like a capacitor on the power supply is bad. Easy fix.

Sep 24, 2009 | Hitachi 50UX57B 50" Rear Projection...

1 Answer

Pioneer SD-P62A3 62" shuts off - won't stay on


If this TV turns back only when it is cooled down than it has cold solder joints tha have to be resolderd.

Jul 07, 2009 | Mitsubishi VS-6055 60" Rear Projection...

1 Answer

Will not power on and stay on


Problem is with the IC.Picture tube is OK.

Jul 06, 2009 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Sound but no picture - won't stay on


you may check your lamp first. other than that i would say a faulty mains board.

Apr 16, 2009 | Samsung DLP HL-P4663W 46" Rear Projection...

1 Answer

Samsung DLP 56' TV turns itself off when I initially turn it own. (I turn it on, then it shuts off for approximately 5-10 seconds and turns back on. Sometimes it does it a couple of times before it stays...


The problem is with the ATT UVERSE HDTV BOX and not the Samsung DLP TV. There is an inherent problem with the ATT UVERSE HDTV Box when using a HDMI cable. This was verified by the ATT UVERSE Technician.

Thanks,

Dec 13, 2008 | Projection Televisions

1 Answer

Samsung TV will turn on and off several times, then stay on.


First, need to check the power bar(if you use).
then. if don't use power bar, need to check the power board.

Dec 12, 2008 | Samsung HL-R7178W 71" HDTV

1 Answer

Samsung HLP5085wx/xaa


i have Samsung HLP5085WX 50" Projection TV
that occasionally turns its self off and then back on again does anyone have any idea what could be causing this

Nov 02, 2008 | Projection Televisions

2 Answers

I have a RCR312W. Other numbers given are R55N7 4811P. The problem is this: Some how it lost it's programming and I don't have the instructions to reprogram it. I tried to do it from memory, but...


  1. These instructions come from the RCA website. The crucial step is to keep pressing the reverse button.
  2. Turn on the component (the tv, dvd, etc).
  3. Hold the TV (or DVD) button and the on/off button at the same time. It will stay lit.
  4. Press the play button every five seconds until the component turns off.
    • Each time the Play button is pressed, the illuminated ON-OFF button blinks ten times and a block of 10 codes is sent to your component. This process continues until all the codes in the Code Lists have been searched. If the component has not turned off after all codes have been searched, the illuminated ON-OFF button blinks four times, turns off, and the Auto Code Search Entry method is exited.
  5. When the component turns off, press and release the REVERSE button, then wait two seconds to see if the component turns on again.
  6. If the component does not respond, continue to press the REVERSE button EVERY TWO SECONDS UNTIL THE COMPONENT TURNS ON again. This will isolate the correct code in the last block of codes sent. Each time the REVERSE button is pressed, the illuminated ON-OFF button blinks.
    • If the REVERSE button is accidentally pressed after the component responds, press and release the FORWARD button. Wait two seconds to see if the component turns off again.
  7. To save the new code, press and release the STOP button.
  8. The illuminated ON-OFF button turns off. You must press the STOP button to save the code.

Jul 09, 2008 | RCA Projection Televisions

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Projection Televisions Experts

The Wyzzyrd

Level 2 Expert

83 Answers

Donald Griswold
Donald Griswold

Level 1 Expert

8 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a Samsung Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...