Question about Sigma SA-7 35mm SLR Camera

1 Answer

Sigmatel S4 not supported with my PC

Sir, I have Sigmatel S4 handset, its not supported with my PC. After i connected with my PC through data cable then i tried on the 3 options on my PC, but the my PC pop-up "the USB is not recognized, Any one please suggest me how can i transfer though data cable..

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert that has over 500 points.

  • Expert
  • 154 Answers

Please install the software given
only the the USB will be recognized

Posted on Oct 21, 2008

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Dimage Z10 won't read card

What type and size card? The Z10 uses SD cards, 2GB or smaller. It will not work with higher-capacity SDHC cards.

Jun 29, 2013 | 35mm SLR Cameras

1 Answer

Unable to download to PC

Try NOT connecting your camera to your computer.

The best way to download pictures from your camera to your computer involves removing the memory card from the camera and plugging it into a card reader (either built-in to the computer or connected via USB or FireWire). This is likely to be faster than connecting the camera to the computer, and won't run down your camera's batteries.

Once the card is plugged in, it will appear to your computer as a removable drive. You can use the operating system's drag&drop facility to copy pictures from the card to the computer's hard drive, the same way you copy any other files. Or you can use iPhoto or any other photo management program.

Jul 15, 2012 | Canon EOS Rebel G 35mm SLR Camera

1 Answer

I have Cannon EOS Rebel xsi. The camera does not take picture when press the shutter in all modes. There is no error message. Have change the memory card, recharge the battery and none work.

Hello Sure !

The probleme :
The Shuteer Has A cable Connected to Recorder
Maybe The cable Has Cutted when you Shut ,or Maybe Cutted When You Charged The Battery cause When your put your camera on the charge , the cable goes be hot and it should be cutted .

Solving The Probleme :
1) I advise You To Change The Cable
2) Push The Reset Button
3) Charge It Again

It works 100%


Aug 03, 2010 | Canon EOS 10D 35mm SLR Camera

1 Answer

My popup flash on my nikon d40 didnt fire when i open the popup, and cant take picture..

Go to service center. it may loose the cable connection. don't fix it. it may lose your warranty.

Apr 14, 2010 | Nikon 35mm SLR Cameras

1 Answer

"ME" flashing on data screen


Thank you for using
FixYa for your problem

Muilt Exposure mode i think it is
Been a little while sorry

Please rate our solutions and if you still have problems please call back for more ideas to help you

Richard Scott
Technical Support
New Zealand

Nov 28, 2009 | Minolta Maxxum XTsi 35mm SLR Camera

1 Answer

Problem in camera or film roll??

Hey msenile,
It is possible that each frame would have image data imprinted without and image being exposed. This could be caused by the shutter not opening while the camera still exposing the film internally with the image data recorded. It is unlikely that this bad film since the emulsion covers the entire surface of the film and if it were bad the image data would not be recorded either. Another cause of this but very unlikely is every frame was somehow extremely underexposed. This could happen if the camera is set to manual and the light level is low and the shutter speed is set to a fast speed and the aperture is set to a very small aperture. I hope this helps!

Go Ahead. Use Us.

Jul 18, 2008 | Nikon F80 35mm SLR Camera

2 Answers

Av is flashing

Make sure the aperture setting on the lens is set to "A". Solved the problem.

Jun 23, 2008 | Pentax ZX-60 35mm SLR Camera

2 Answers

Light meter problem and blank developed film

I'm afraid you have a somewhat serious problem. There is a tungsten cable that runs from the speed dial to the rewind side if the camera. This cable sets the brushes for the electrical contacts the are under the rewind assembly. Adjusting speeds or ASA changes the position of the contacts.

It is very likely that the cable has broken and needs replaced. Canon no longer supports these nor do they have parts

Feb 10, 2008 | Canon EOS-AE-1 35mm SLR Camera

1 Answer

Problem with lens

I can't understand if besides the noise the camera works or not... If noise is the only problem, then its normal for the camera to make noises, especially from the lens since it has moving parts. Please post your problem again and try to describe the problem itself in more detail. Otherwise try following the manuals instructions on a soft and hard reset of the camera, which might solve your problem. You can get a copy of the manual here on fixya from the product page. If there is no reset procedure on the manual try disconnecting it from any power source for a few days(batteries, cable etc), and then try again. Also try replacing the batteries with new ones. Good luck!

Mar 13, 2006 | Olympus IS-20 QD 35mm SLR Camera

Not finding what you are looking for?
Sigma SA-7 35mm SLR Camera Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sigma 35mm SLR Cameras Experts


Level 3 Expert

96733 Answers

old marine
old marine

Level 3 Expert

1479 Answers

Ric Donato

Level 2 Expert

225 Answers

Are you a Sigma 35mm SLR Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides