Question about Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

Wheel shaft seals on troy bilt pony 7 hp.

I know I need to replace the wheel shaft seals on the left side of tiller. My question; Is it possible to remove the old seal and replace it with a new one without taking the transmission apart?

Posted by on

  • Anonymous Mar 22, 2014

    how to remove oil seal on tiller shaft on john deere 624 tiller

  • Anonymous Mar 23, 2014

    if you turn steering wheel to the right tires turn to the left

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

If the seal fits over the axle shaft it should be ok. be sure your axles are very clean as not to ruin the new seals when applying them. probably a good idea to replace them as a pair (right and left side) to save you time down the road.

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 5 hp troybilt pony tiller. The axle seals need replacing can you describe the best way to replace them. This tiller was built in Feb. of 1990.


http://www.mtdparts.com/webapp/wcs/stores/servlet/OperatorManualView?storeId=10101&catalogId=19502&langId=-1

Go to this website and type in PONY for your model number and find your operator manual by your serial number. The operator manual should have detailed instructions on how to replace your seals.
On the Horse model you remove the wheels and then carefully use a couple of screw drivers to pry out the old seals being careful not to scratch the wheel shaft sealing area. Then polish the wheel shaft with fine emery cloth to remove any sharp edges. Then grease the wheel shafts and carefully slide the new wheel seals on and use a piece of plastic PVC pipe cut square that will slide over the shaft and gently drive the seal to the depth the old seals were installed at. You dont even have to drain the gear oil. Getting the wheels off the wheel shaft is sometimes a problem if they are rusted on. if you can get the wheels off its not to hard to change the seals.

Frank

Sep 13, 2010 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

Troy-bilt horse engiine runs good , tines work,


The wheel shaft on a Horse tiller is one piece so if the shaft turns on one side it will turn on the other. make sure the pin that holds the wheel on is not missing that would let it spin on the shaft.
That's the only thing I can think of that would cause that problem. Hope that helps.

Frank

Aug 29, 2010 | Troy-Bilt Power Tillers & Cultivators

1 Answer

Wheel removal troy bilt horse.


Make sure that when you heat that you heat the wheel assembly only and not the axle. If the heat gets directly to the axle it will expand and the heat does no good.

Apr 04, 2010 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

2 Answers

Old Troy Built with model #HH60-105106F. What is


That's the engine number. It's a 6Hp Tecumseh. Go on ebay and buy the Troy Bilt parts manuals on CD for Horse Roto Tillers (if that's what it's on). I paid $8. Definitely worth it.

Mar 08, 2010 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

I cannot get my oil seals of my rear tine tiller It is a Troy Bilt 5.5 hp and I got the left side off but the right side tine attachment will not budge any suggestions please


Have you tried soaking the shaft area with either PB Blaster or Deep Creep penetrating oil. Try this for a few days before trying to tackle getting the tine attachment off.

Jan 26, 2010 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

I need to replace the seals on my Troy-Built Pony tiller. 6 hp, ser.# 121811201149. I can not seem to remove the tine shafts. I have pulled the bolt thru the shaft but cannot budge it. Does anyone know...


I presume you opened the port and removed the grade 8 placement bolt? If you have then you need to polish the shafts with 400 then 800 sandpaper, clean then lube them before trying to slide thru the support bearings. If your tine shaft is bent? your screwed, or just remove the shaft seals with a screwdriver and replacing them without removing the shaft. REmember to put a thin coat od RTV arround the outer lip to help make a better seal

Nov 15, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

2 Answers

How do I change the belts on a troy bilt tiller


remove plastic belt cover
remove the guard,belt/pulley
work in the right side first:
remove the rigth-side wheel
remove the screws of the bumper
remove 2 screws on bracket/transmission assembly
pull the bracket
install the new belt
reinstall the right side screws and wheel

do the same in the left side
Ps: remove the belt guide, and reverse return spring
http://www.partstree.com/parts/?lc=troy_bilt&mn=21A-634K766+7HP+FRT+Roto-Tiller+(2005)&dn=0079200009

May 06, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

1 Answer

Troy bilt pony left side tine assembly fell off


sounds like the shaft is either bent,or the inside diameter is worn and the shaft tube needs to be replaced.

Apr 23, 2009 | Troy-Bilt Pony Garden Tiller

1 Answer

Changing the drive belt


remove plastic belt cover
remove the guard,belt/pulley
work in the right side first:
remove the rigth-side wheel
remove the screws of the bumper
remove 2 screws on bracket/transmission assembly
pull the bracket
install the new belt
reinstall the right side screws and wheel

do the same in the left side
Ps: remove the belt guide, and reverse return spring

http://www.partstree.com/parts/?lc=troy_bilt&mn=21A-634K766+7HP+FRT+Roto-Tiller+(2005)&dn=0079200009

Apr 12, 2009 | Troy-Bilt Pony Garden Tiller

3 Answers

Oil seal for rear tine shaft


The serial number is located on a flat spot just above the right wheel shaft where the gear housing and the top gear cover meet. It will be a six digit number stamped in the metal.

Frank

Mar 11, 2009 | Troy Bilt Pony 6.5 Hp Rear Tine Tiller

Not finding what you are looking for?
Troy Bilt Pony 6.5 Hp Rear Tine Tiller Logo

1,056 people viewed this question

Ask a Question

Usually answered in minutes!

Top Troy Power Tillers & Cultivators Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers

Dwain Pippen

Level 3 Expert

376 Answers

Wade Mobley
Wade Mobley

Level 2 Expert

448 Answers

Are you a Troy Power Tiller and Cultivator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...