Question about Hoover H130E Front Load Washer

1 Answer

Very noisy machine

A bra bone has caught somewhere in the machine. very noisy have tried to empty filter nothing haooened. can i remove the object myself

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 641 Answers
Re: very noisy machine

You can remove it by yourself. Disconnect machine power cable !!! Open washer's main access panel and then remove the pipe connected between the pump and the bottom of the outer tub. Open it first on the pump side and if you will not find there the bra bone, remove the large-diameter rubber hose that connects the bottom of the tub. keep a rag nearby to dry up spillage of water when removing the rubber host. Good luck !!

Posted on Jul 03, 2006

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer


First problem could be a bra wire or something similar caught in the holes in the bowl or between the bowl.Also you could have faulty bearings.Have a close look and see if it is in the holes first.Let me know how you go.

Apr 19, 2011 | Whirlpool Washing Machines

1 Answer

Machine very noisy when it spins. Missing bra

If you cannot here it catching, then leave well alone, if it is still catching, then you could to try to locate it by removing the lower rear cover of washer, remove the large black hose on bottom of drum, and see if you can locate it from the bottom of the drum.
Hope this helps.

Jan 16, 2010 | Hotpoint Ariston Aquarius WD420 Front Load...

1 Answer

Indesit 1600 WIE167 washing machine

locate element and remove you should then be able to remove bra wire they normally get caught around element

Jul 01, 2009 | Washing Machines

2 Answers

Bosch Maxx WFL 2260 not draining - nothing in filter - help?!

sounds like a simularproblem i had, a 5cent piece got caught in the drain solenoid (just between the drum and solenoid) , i had to lift up the front and spin the drain pump fan, on empty, then disassemble and clean pump assy and remove 5cent piece, hope this helps.

Jan 25, 2009 | Washing Machines

1 Answer

Bra wire stuck somewhere in machine

You will not see it as it is trapped between the inner and outer drum, what you need to do is remove rear panel and the large hose from the pump to the bottom of the drum,
Then reach in with your fingers and see if you can feel it , if you can't then short of removing the drum (not recommended) ther is not a lot you can do, hopefully it will find it's way into the filter, where it wiil not be a problem
Plz rate this solution.

Dec 15, 2008 | Washing Machines

1 Answer

Lost bra bone in washing machine

I happen to find these in the water pump or just bellow the drain hose from the tub. If not carefull, these can puncture the door boot, if front loader.

Oct 22, 2008 | Washing Machines

2 Answers

Zanussi turbo dry 1050 goes through cycles but will not spin or drain so is full of water what can i do

check filter (bottom rhs side. if still no joy, then maybe foreign object in pump

Jul 13, 2008 | Washing Machines

1 Answer

Wf540 hotpoint washing machine making a banging noise

remove lower front panel pump right of center turn small plastic handle counter clockwise pull out

May 31, 2008 | Hotpoint Aquarius WF000 Front Load Washer

3 Answers

Water will not empty

you either have a blockage in the filter or you pump is not working.
how to check is diconnect the waste pipe and lower it to ground level if the water does not empty then its a blockage. if it empties then its the pump.
other things it can be is a blockage where the waste pipe is connected or a loose wire to the pump..

Dec 13, 2007 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Washing machine Drum rattles

It is probably between the clothes tub and the outer tub. To remove it from the outer tub port, open the washer's main access panel and remove the large-diameter rubber hose that connects the pump to the bottom of the outer tub and try to remove the clothing through the port. Good luck

Aug 03, 2006 | AEG Lavamat W1050 Front Load Washer

Not finding what you are looking for?
Hoover H130E Front Load Washer Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hoover Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Chris Hall
Chris Hall

Level 3 Expert

842 Answers

Are you a Hoover Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides