Question about Ruud Heating & Cooling

1 Answer

I have rudd quiet 80 series the flame ignites then the flame goes out and just blows air

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 182 Answers

The flame sensor is dirty.

Posted on Oct 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a rheem classic quiet 80 . furnace starts up but the igniter will not kick in to start the flame


This problem can be one of two things:

1) Bad igniter.

2) Control board not sending 120 volts to igniter.

You will need a multimeter to verify if the igniter is receiving 120 volts.

Sep 07, 2015 | Heating & Cooling

1 Answer

Burners turn on for 10 sec and shut off


going out on safety. either high limit or failure to detect flame.

Dec 14, 2013 | Ruud Central System Air Conditioner

1 Answer

I have a rudd hot air gas furnace,ignitor sparks


to carmelmontgo; do you have a smart gas valve sometimes the wire connections get loose. remove wire connector then reinstall. also cleaning a flame sensor will work if the flame sensor is good. I would check the ground connection sometimes contaminated with rust. also I would check the gas pressure with a gas manometer...my email is alpharomeo@windstream.net

Jan 20, 2010 | Ruud UBHC Air Conditioner

1 Answer

The gas sometimes ignites and the goes out and


Check out my tip. I think it will fix your problem.

Jan 04, 2010 | Heating & Cooling

1 Answer

We have a Rudd acheive 90 plus (11 years old) that fires but will not stay running. Any suggestions?


I have not worked on any Rudd 90s but in some furnaces a flame sensor on the opposite side from the igniter can get dirty. It looks like a 0.08 " wire sticking out of a ceramic holder.Cleaning the wire with scotchbright will often cure the problem . Good luck

Nov 04, 2009 | Ruud UBHC Air Conditioner

1 Answer

Rudd achiever serie. where do the 24 volt wires go to on the air handler.


The two wires from condensing unit go yellow or y from Tstat and theother wire goes brown if it is a Rudd or Rheem. Red from Air HAndler goes to Tstat R Green to Tstat G white to w. If it is digital tstat brown goes to C.

Jun 04, 2009 | Ruud UAMB Air Conditioner

2 Answers

My rheem quiet 80 ignition flame keep going out. it'll turn on and then go out.


I have a Rheem Classic 80 furnace that would ignite but not stay lit. Cleaned the ignition sensor which was easy to get to and the flame sensor which was under the burner plate and it fired up and stayed lit. The flame sensor was about 6" under the burner plate. Easy to get out, but tough to get back in. Used the old piece of paper shim trick to get the screw to "stick" in the socket and it was much easier to position the screw and get it back where it belonged.

Jan 16, 2009 | Heating & Cooling

2 Answers

Ruud Silhouette II Fails to Ignite


sounds like you have bad flame sensor or the sensor is in a bad postition. To get eliminate the lockout turn the power off to the unit and back on again. Look at the circuit board light and see what the troubleshooting code is.

Jan 13, 2009 | Heating & Cooling

1 Answer

(HVAC) Furnace Not Igniting Quickly


Make sure a back draft in the flue is not happening. Wind can blow it out until the flue heats up. The flame sensor may not be close enough to the burner flame. It may be weak and need to be replaced or if its an optical one it may be dirty and not see the flame very well. Its not wasting much gas but it puts extra wear and tear on the gas controls, is noisy, and, as you said, blows cold drafty air. A gas control system that has issues of any kind is not real safe. It needs to get fixed.

Jan 08, 2009 | Carrier XHB123D X/Y Series Heat/Cool Air...

1 Answer

Furnace sometimes will not stay lit


Check the heat exchanger for a crack or hole. The room air blower is blowing back into the heat exchanger extinguishing the flame. Have it checked out today. Did you get it checked yet? Now. Have I stressed to you to get it checked out yet or have you been overcome by Carbon Monoxide yet?

Dec 10, 2008 | Carrier XHB123D X/Y Series Heat/Cool Air...

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ruud Heating & Cooling Experts

Bill Long

Level 3 Expert

587 Answers

Tim Whalen

Level 3 Expert

3069 Answers

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Are you a Ruud Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...