Question about Zenith DVB412 DVD Player

3 Answers

Programming remote for Zenith DVB412 DVD Player

Okay, on the remote, there is a TV power button. I am trying to figure out how to program the remote to turn on/off and change channels on my Sharp TV. There is no programming information in the manual. How do I program it?

Posted by on

  • Anonymous Mar 12, 2014

    Hitachi TV remote will program to gpx DVD player

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Here is the response from LG/Zenith customer support:

Unfortunately, this remote has very limited programmability. The manual is correct.

INSTRUCTIONS: Controlling other TVs with the remote You can control the sound level, input source, and power switch of non-LG TVs as well. If your TV is listed in the table below, set the appropriate manufacturer code.

  1. While holding down TV POWER button, press the number buttons to select the manufacturer code for your TV (see the table).
  2. Release TV POWER button. Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.

Manufacturer Code Number
LG/GoldStar 1 (Default), 2
Zenith 1, 3, 4
Samsung 6, 7
Sony 8, 9
Hitachi 4

For further information or troubleshooting, you may contact us at 800-243-0000 for LG Customer Service assistance. An agent will be glad to assist you. Please feel free to contact us with any additional questions or concerns. Thank you again for contacting LG Electronics.

Posted on Feb 17, 2009

  • Hugo Martinez Jan 23, 2011

    Thank you nobby411, this work on my Sony TV using number 8 option.

    Hugo from Monterrey México

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Hi there!

 

I have the exact same problem...am wanting to program this same remote to control the TV. 

 

There are no instructions in the manuel...however, in my hours of searching for information on "how to," I did discover that this LG manufactured remote is a "universal" remote.  Unfortunately, the Owners manual fails to address the TV Control feature.

 

This same remote was manufactured for Zenith's Allegro ABV441 and ABV511 DVD/VCR, Goldstar GBV-441, LG VC8410MS and VG8610MK, and as  Zenith Remote 6711R1P070H.  I've check the manufacturer's web sites and there is virtually no information on this remote.

 

I did come accross Zenith's Customer Support #, (888) 865-3026.

 

Hope this helps!

Posted on Oct 17, 2007

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 50 Answers

Hi I'm not familiar with that specific model, but if there is no programming instructions in your manual, then the remote is probably not a "Universal Remote". If they don't advertise the remote as being universal in your manual, then the TV controls have been put on your remote so that if you buy your Zenith DVD as part of a package deal that includes a Zenith TV, you can use that one remote to operate both, but they must both be Zenith product. (They also hope to encourage you to buy a Zenith TV to go with your DVD player, if you don't have one) Hope this helps!

Posted on Jul 26, 2006

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to program the remote control for a Zenith VCR and DVD combination player go to


If it is the original remote control for your TV - VCR & DVD it doesn't need programming but guess it's not, so you can't program it.
You need some unviersal remote where all three devices shold be listed, and code it setting for each devicer

Jun 08, 2015 | Zenith Televison & Video

1 Answer

Samsung AK59-00123A remote to a M261VP vizio tv


Hello

[1] Switch your television on

[2] Point the remote control towards the
television

[3] Press and hold the TV POWER button, and

then enter the two-figure code in the table

to the right that corresponds to the brand of

your television by pressing the appropriate

number buttons.

If your television is compatible with the remote

control, it will switch off.

The remote is now programmed to operate
the TV.
The code for Zenith TV is [TV POWER + 63]

Sep 20, 2011 | Zenith ZEN700 Remote Control

1 Answer

Zenith DVD player DVB412 is requiring an entry for a Parental Control Limit on a brand new Across the Universe DVD. I've tried 0000, 3308 to reset the code, the reset button. It looks like others had...


Hello Hummer,

Please follow the instuctions below to reset the password and switch off the parental control on the Zenith DBV412.

1. Switch on the TV and DVD player
2. Switch the TV to the input for the DVD player
3. Remove any disc from the player
4. Press the SETUP key on the Zenith remote to open the on-screen menu
5. Press 2 1 0 4 9 9 using the numerical keys on the Zenith remote.
6. Press SETUP again to close the menu

This will clear any password that has been set. Now you need to switch off the parental control:

8. Press the SETUP key to open the on-screen menu again
9. Use the down arrow to highlight the PADLOCK for the parental control settings
10. Press the RIGHT arrow once to enter the parental control menu
11. Highlight RATING and press the RIGHT arrow once.

You will be asked to set a password. Enter something simple and easy to remember, e.g. 0000 then press ENTER. You will need to confirm the password by entering the same number again, then press enter again.

12. Use the UP/DOWN arrows to highlight UNLOCK then press ENTER
13. Press SETUP again to close the menu

You should now be able to insert your Across the Universe disc and play it. If you are still unable to watch the disc or you are unable to switch off the parental control feature, please let me know.

Regards,
BElectric

Apr 09, 2011 | Zenith DVB412 DVD Player

1 Answer

How do i program my remote


Hello;

Without knowing the codes for the specific brand names and models of your devices, this is how you program the Zenith MBR3447 for your TV, VCR, DVD Player, CD Player or Audio Receiver:

TV

1. Push the "Power" button on the TV to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "TV" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the TV's IR sensor and push the "Power" button. Pause a second. If the TV fails to shut off, push the "Power" button again. Repeat until the TV does shut off. Each time the "Power" button is pressed the Zenith MBR3447 tries using a different TV device code from its code library to turn the TV off. Therefore, when the TV finally does shut off it's an indication that the remote is temporarily programmed with the correct device code to control the brand of TV you're using.
6. Press "Enter" to save the current code.

VCR

1. Push the "Power" button on the VCR to turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "VCR" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the VCR's IR sensor and push the "Power" button. Pause a second. If the VCR fails to shut off, push the "Power" button again. Repeat until the VCR does shut off. Then press "Enter."

DVD Player, CD Player or Audio Receiver

1. Push the "Power" button on the device your programming the remote to control to manually turn it on.
2. Press and hold the "PRG" button in the upper left corner of the remote. Release when the indicator light, located in the top center of the remote control, comes on.
3. Push the "AUX" mode key located at the top of the remote.
4. Enter 0 -- 0 -- 0 on the remote's number pad, then press the "Enter" button.
5. Aim the remote control in the direction of the device's IR sensor and push the "Power" button. Pause a second. If the device fails to shut off, push the "Power" button again. Repeat until the device does shut off. Then press "Enter."

Mar 11, 2011 | Zenith MBR3447 Remote Control

1 Answer

I need a new remote control for dvd player brand zenith remote No.6711R1P070H DVDplayer DVB412. Because mine is broken.


Try Logitech's Harmony 600 Universal remote. It costs about $80.00 Cdn but is excellent for most infrared activated TV's and DVD players. Codes are installed by the site at the point of online programming, so no need to search for codes or install them manually one-by-one.

Feb 20, 2011 | Televison & Video

1 Answer

I inherited a Zenith DVB412 from a relative that passed away. I am trying set it up with my Magnavox TV/Dish network. I am struggling to find the manufacturer's code. I looked in the usefr's manual but...


Here is a link to our online troubleshooting there are codes and instructions here.
http://www.dishnetwork.com/downloads/pdf/user_guides_and_manuals/Remote_Codes_Web_Page.pdf

Daniel Busa
DISH Network Customer Service

Dec 02, 2010 | Zenith DVB412 DVD Player

1 Answer

Im trying to program a remote the tv is a zenith


Configuring codes:
1.Turn on a desired device (VCR or DVD player)

2. On the remote control, press a device key once (i.e., DVD/VCR,
CBL/SAT or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo, or TV/VCR/DVD Player Combo press DVD/VCR once. After programming a VCR Combo device, you will be able to control channel selection,volume, and VCR functions.

To program control of a DVD Player,DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After programming a DVD Combo device, you will be able to control channel selection, volume, and DVD functions.

To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

3. Press and hold SET until the LED (red light) blinks twice,
then release SET.

4. Use the Manufacturer’s Codes to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly,
the LED will blink twice.

5. Aim the remote control at the device and press POWER once. The device should turn off. If it does not, repeat steps 2 to 5, trying each code for your brand until you find one that works. If it still doesn’t work, try Searching For Your Code on next page


Auto Code Scan:
1.On the remote control, press TV once.

2. Press and hold SET until the LED (red light) blinks twice, then release SET.

3. Enter 9 - 9 - 1.The LED will blink twice.

4. Aim the remote control at the TV and slowly press POWER button.Stop when the TV turns off

5. To lock in the code, press and release SET.The LED will
blink twice.

6. To search for the codes of your other devices, repeat steps
1 to 5, but substitute the appropriate device key for the device you are searching for.


Thanx

Aug 06, 2010 | One For All URC4110 Remote Control

1 Answer

I don't know the code or how to program it to my magnavox tv or zenith dvd/VCR player


Hi,

Manual code entry

1.Turn on your television or other electronic component that you want to program the remote control for.

2.Hold down the "Code Search" or "Setup" button until the LED indicator light turns on.

3.Hit the button for the component that you are programming (TV,DVD VCR, etc.). The LED light should flicker and stay on.

4.Enter the 3-digit or 4-digit code that corresponds to the TV or device that you're operating.The LED light should go off if the code is valid, but will flash if it is not. Try other codes you have.

5.Try turning the television or other programmed component off to ensure that the remote works properly, once the light has gone off.


Auto configuration


1.Turn on your television or other electronic component that you want to program the remote control for.

2.Hold down the "Code Search" or "Setup" button until the LED indicator light turns on.

3.Hit the button for the component that you are programming (TV, DVD, VCR, etc.). The LED light should flicker and stay on.

4. Press and release the "Power" until the television or other component turns off while waiting at least 2 seconds between each press.

5.Press "Enter" or "Save" once the remote has effectively turned the power off. The LED light will shut off and the remote will now operate the device.


You can get your codes from below website

http://www.jascoproducts.com/support/universal-remote-codes.asp

Thanx

Aug 05, 2010 | GE RM24912 Universal Remote Control

1 Answer

I have a Mitsubishi VS-45605 projection TV and a Philips DVD player model DVP3962/37. Can anyone help me figure out how to program the remote to control the DVD player? I only have the original remote for...


I've got the same tv and...I've still got the manual!;-)

Programming the Remote to control other audio and video products:
  1. Move the slide switch at the top of the remote to select the a/v product you want to control (in this case, DVD).
  2. Press and hold the Power button so that it stays down when you enter the code.
  3. Enter the code for the equipment. Release the Power button
  4. Point the remote at the equipment and press the Power button. If the equipment respondes, you're done. If not, and you have more codes that apply to that equipment, go back the step 2 and try the next number.
If none of the numbers work, I'm afraid you might be out of luck.

Oct 20, 2009 | Mitsubishi VS-45605 50" Rear Projection...

1 Answer

CODE FOR ZENITH DVD PLAYER


Try this out and if it does not work your remote might not support your unit.
Code Search:
  1. Turn on the device you wish to control.
  2. Press and hold "CODE SEARCH".
  3. Press and release the TV, VCR or Cable button. If programming an AUX position, press and release AUX first and then press the device type to be programmed.
  4. Release "CODE SEARCH".
  5. Press ON/OFF repeatedly until the device turns off. You may have to do this up to 100 times.
  6. When the device shuts off press and release ENTER.
  7. Try using the remote. If it does not function repeat steps 1 through 6.
Hope this helps. :}

Mar 18, 2008 | Televison & Video

Not finding what you are looking for?
Zenith DVB412 DVD Player Logo

2,234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zenith Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75774 Answers

matt martin
matt martin

Level 3 Expert

1229 Answers

Jaime Hernandez

Level 3 Expert

2336 Answers

Are you a Zenith Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...